文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 医药卫生 > 临床医学 > Powder Forging of a Motorcycle Connecting Rod (1)
侵权投诉

Powder Forging of a Motorcycle Connecting Rod (1)

外文翻译

544

J. Mater. Sci. Technol., Vol.18 No.6, 2002

Powder Forging of a Motorcycle Connecting Rod (1)

Powder Forging of a Motorcycle Connecting Rod

Guangchun WANG and Guoqun ZHAO

Mold & Die Engineering Technology Research Center, Shandong University (Southern campus), Jinan 250061, China

Manuscript received June 25, 2001, in revised form September 5, 2001]

A motorcycLe connecting rod is one of the major moving parts affecting the engine performance. The traditional manufacturing process results in material waste and excessive machining. A new method of hot forging P/M has been proposed and studied experimentally. In order to achieve uniform density, the punch was divided into three parts to consolidate the loose powder. The multistage movement of the three parts of the punch, called synchronous compaction, results in the desired uniform density. Powder flow during consolidation was illustrated and the density distribution of the compacts was measured. A set of forging dies with flash was used to produce densification and deformation of the sintered compact. Then a set of flashless forging dies was designed to obtain the desired shape and dimensions of the connecting rod. The effects of forging temperature and initial compact density on densification were evaluated through hot forging experiments. Based on properties achieved, Fe-C-Cu-Mo was selected as the alloy powder. Through testing and metallographic observation the physical and mechanical properties of the connecting rod produced by the P/M hot forging were found to be superior to those manufactured by the traditional method.

KEY WORDS: Powder metallurgy, Connecting rod, Powder forging

1. Introduction

Powder metallurgy(P/M) is one of several net or near net shape processes for the manufacture of structural metal parts. Due to low cost in material and time saving in the consolida-

tion and sintering processes, more and more P/M parts are being used on cars and motorcycles. But P/M has an obvi-

ous disadvantage. It is difficult to achieve alloy steel level on density and mechanical properties. Although some processes, such as complex pressing, injection molding, selecting prea-

lby powder and warm pressing, can be used to try to obtain a fully densified part, the density can not reach 96% of thea-

retical donsity. On the other hand, the above processes also increase the cost significantly.

Powder forging, combining powder metallurgy and forg-

ing process, has proved an effective method to improve density Figi. Shape and dimensions of tke motorcycle connecting

and strength of sintered parts”31. Federal-Mogul company rod used for experiment

of the United State, GKN company of England, Hoganas com-

pa n of Sweden and GKN company of West Germany used the ing rod after forging without the trimming and hole drilling. powder forging process successfully to produce a large number Furthermore, the properties of the forged sintered compact of hgh strength P/M parts, including car motor connecting can achieve those of alloy steel, and may even exceed them.

rod, internal and outside ring of auto-gearbox, belt gear, ex-

In this paper, the motorcycle conuectiug rod designed by ternal ring of clutch coupling and so on’1. Powder forging Qingqi group of China was used for the powder forging exper-

process results in savings in energy and material in addition iment. The shape and dimensions of the connecting rod are to improving mechanical properties of the P/M parts.

shown in Fig.1. The original material used in the traditional process is 2OCrMo.The hardness of pin ends and inner holes A motorcycle connecting rod is one of the moving parts is HRC5S- 62. The crank hardness is HRC34.

of the engine. It converts a pistoa rectilinear motion into reciprocation revolving motion. In the motorcycle industry,

weight reduction is beneficial to the reduction of gas emission 2. Experimental

and vibration and improvement of engine performance. The

connecting rod has strict performance requirements, includ-

Experimental study on powder forging of the connecting ing its mechanical properties such as tensile strength, bend-

rod had two tasks. One was to determine component details ing strength, wear resistance, fatigue resistance and impact of P/M alloys with good mechanical properties and consol-

strength. The annual production of the motorcycle connect-

idating process for uniform density. The other was to obtain

ing rod is very large in China at present. In the current pro-

the reasonable P/M and hot forging parameters. The research cess, the finished product is manufactured using an alloy steel procedures were divided into the following three steps:

rod through a series of working procedures including crop-

1) Designing compaction die and compacting process. ping, forging, trimming, hole drilling, protecting percolation 2) Researching the effect of different powder types on com-

treatment, hole boring, carburization, quenching, tempering, pacting, sintering, and properties of compacts.

sand blasting and fine-wearing. It wastes much material and 3) Designing the powder forging die and researching the time due to excessive machining. The powder forging pro-

effect of densification and deformation of sintered compact on cess for fabricating the connecting rod, instead of the cur-

the properties of the final forged parts.

rent process, has some advantages. Since a sintered compact

approaches the shape of part, boring and fine wearing are 2.1 Design of consolidating die and consolidnting process

enough to satisfy the geometrical requirement of the connect-

Design of the consolidating die does not depend simply

upon the shape and dimensions of the part. The powder forg-

ing parameters and the strncture of the forging die must be

Professor, Ph.D., to whom correspondence should be addressed. E-mail: wgcsdu.edu.cn

4

第1页

你可能喜欢

热门文档

相关文档

  • 制造工程与技术(热加工)英文版14 Forging of Metals

    – by forging – by casting – by powder metallurgy(粉末冶金) – by ...removing flash Figure 14.7 (a) Stages in forging a connecting rod for ...

  • 05金属锻造forging of Metals

    Costs of a Rod Made by Forging and Casting Figure 14.19 Relative unit costs of a small connecting rod made by various forging and casting processes. ...

  • Forging

    powder metallurgy or casting, or a preformed blank from a prior forging ...s shape gradually changes, as shown for the forging of a connecting rod....

  • Connecting_Batteries_and_Chargers_in_Series_and_Par...

    Powder+Forging+of+a+Mo... 暂无评价 6页 1下载券 Connecting rod is an i... 2页 免费 The Finite Element Ana... 4页 2下载券 connecting rod(曲柄连...

  • 中国连杆锻造的发展回顾

    [2] Q.L. Luo, Improved production technology of motorcycle forgings, ...Lei, New technology for precision forging of connecting rod, J. Jinan Univ...

  • 金属的锻造ForgingofMetalsCh14

    Costs of a Rod Made by Forging and Casting Figure 14.19 Relative unit costs of a small connecting rod made by various forging and casting processes. ...

  • PowderForgingofaMotorcycleConnectingRod

    PowderForgingofaMotorcycleConnectingRod 隐藏>> 5 44 J . t Ma e r . Sei . e T e hn o l厂 b l18 V . . N o . 6 , 2002 P G w o u ...

  • Diesel engine connecting rod processing

    Diesel engine connecting rod processing Abstract The connecting rod is one of...Two holes can not directly, forging Work. By looking at more than ...

  • ...Gripping Mechanism Clamping Force of Forging

    Gripping Mechanism of Forging Manipulator Structure Composition. The gripping mechanism is made up of pushing rod, connecting rod, clamp and clamping cylinder...

  • Conrod

    Conrod_机械/仪表_工程科技_专业资料。connecting rod manufacturing processJanuary...densification of a heated powder-based preform using a single forging strike...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email