



GONG Wei-huai1, CHEN Yu-hua1, 2, KE Li-ming1
1. National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology,
Nanchang Hangkong University, Nanchang 330063, China; 2. State Key Laboratory of Advanced Welding and Joining,
Harbin Institute of Technology, Harbin 150001, China
Received 3 September 2010; accepted 24 February 2011
Microstructure and properties of laser micro welded joint of
TiNi shape memory alloy
Abstract: Butt welding of 0.2 mm-thick TiNi shape memory alloy sheet (SMA) was carried out using impulse laser, and tensile strength, fracture morphology, microstructure and phase change behaviour of welded joint were studied. The results show that using impulse laser can realize good butt welding of TiNi SMA sheet, tensile strength of welded joint is 683 MPa, which achieves 97% of that of cold rolled base metal, and the fracture mode of welded joint is ductile type as well as base metal. The welded joint can be divided into four zones according to grain size and microstructure. The microstructures of welded seam center zone are fine equiaxed crystals and the microstructures of both lower surface and upper surface edge zones are columnar crystals. When welded joint is vacuum annealed after welding, the phase transformation process is basically similar to the annealed base metal.
Key words: TiNi shape memory alloy; laser micro welding; microstructure; properties; phase transformation behavior
with an numerical control alternating current resistance welding machine and CuNi filler. Laser welding is one 1 Introduction
of the most important joining techniques for this class of
materials because appropriate control of the process TiNi shape memory alloy (SMA) is a new kind of
parameters can ensure good reproducibility of the results. functional material with good shape memory effects
HSU et al [11] joined 2 mm-thick TiNi SMA with CO2 (SME), super elasticity (SE) and good bio-compatibility
[1 4], so it is used in many fields such as medical device, laser and studied the SME and corrosion of welded joint. instruments, aviation, space-flight, atomic energy and TUISSI et al [12] and FALVO et al [13] investigated the ocean development [5 6]. However, successful effects of the laser Nd:YAG welding on the functional applications of any novel material not only hinge up on properties of the NiTi SMA. The results show that the its inherent characteristics, but also depend on solving two-way shape memory effect is partially preserved in problems of welding technologies [7]. But, only a few the welded material; however, higher values of plastic welding techniques for joining NiTi alloys have been strain with respect to the unwelded material, were reported in literature up to now. Tungsten inert gas (TIG) observed. GUGEL et al [14] realized joining of thin welding causes marked degradation in the mechanical pseudoelastic NiTi wires (100 μm) with an Nd:YAG properties of the joint due to an extended heat affected laser and studied the performance of the joints in static zone [8]. XU et al [9] studied the welding ability of 2 tensile tests and their functional fatigue. The results mm-thick TiNi SMA by high energy plasma beam showed that the welded joints reach about 75% of the method, good formation of weld is obtained and the ultimate tensile strength of pure NiTi wires. YAN et al tensile strength of welded joint reaches 750 MPa which [15] investigated the electrochemical behaviors of is 62.2 % of that of the parent metal and the fracture laser-welded Ti-50.6%Ni SMA and the base metal in appears in the center of weld. XUE et al [10] realized 0.9% NaCl solution by electrochemical techniques resistance brazing of 2.5 mm×1.2 mm TiNi SMA wire such as corrosion potential measurement, linear and
Foundation item: Project (200804) supported by State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, China Corresponding author: CHEN Yu-hua; Tel: +86-791-3863023; E-mail: ch.yu.hu@163.com DOI: 10.1016/S1003-6326(11)60970-9
黑龙江哈尔滨150001)(2.南吕航空人学,江西南昌330063) 摘要:采用微型脉冲激光对0.2mm厚的薄片状TiNi形状记忆合金/不锈钢异种材料进行对接焊,研究了接头的微观 组织...
利用光学显微镜,扫描电镜,微区XRD等分析测试手段,研究了TiNi形状记忆合金丝激光焊接头的微观组织特点。为研究接头的力学性能和形状记忆效应,对其进行拉伸和弯曲试验。...
TiNi形状记忆合金与不锈钢激光钎焊接头界面组织特征_专业资料。通过扫描电子显微镜、能谱仪及X射线衍射技术分析TiNi形状记忆合金与1Cr18Ni9Ti不锈钢激光钎焊接头界面反应...
TC4钛合金激光焊接接头组... 4页 免费 TiNi形状记忆合金片激光... 5页 1...形貌, 研究了接头的微观组织和性能, 分析了晶间析 出相物对接头性能的影响。...
预置填充稀土激光焊接对TiNi形状记忆合金微观组织及成分的影响_专业资料。采用Nd—YAG连续激光器对Ti—Ni50.9at%形状记忆合金进行焊缝预置填充材料激光焊接,预置填充...
能焊和激光钎焊焊接 TN 形状记忆合金与不锈钢异质接头 , ii 研究 了接头 的力...口形貌和微观组织.结果表明 : 采用微束等离子 弧焊和储能焊 , 焊接接头极脆 ...
作者在 TiNi 形状记忆合金激光 对接接头的焊缝中预置填充混合稀土元素,改善了激 光焊缝组织性能,对记忆合金的激光焊接领域拓展有 更好的前景。 1 1.1 实 验 ...
试验研究了TiNiNb宽滞后形状记忆合金Nd:YAG激光焊接的组织与性能。通过光学显微镜...β-Nb在TiNi基体相晶界和晶内分布不均匀;接头各区域的显微硬度均高于母材;室温...
喜欢此文档的还喜欢 TiNi形状记忆合金片激光微... 5页 2财富值... 微观组织演变对ZK60合金搅拌摩擦焊接接头的力学性能的影响(英文) 隐藏>> ...
No.10 October 2008 预置填充稀土激光焊接对 TiNi 形状记忆 合金功能性的影响...激光焊接接头的组织与原母材组织有明显变化,在瞬 时高能量密度的激光源作用下,...
热门文档