冶金

Effect of Cooling Structure on Thermal Behavior of Copper Plates for Slab Continuous
Casting Mould
Xiangning MENG, Weiling WANG, Miaoyong ZHU
School of Materials & Metallurgy, Northeastern University, Shenyang 110819, P. R. China
Contact Email: xn_meng@126.com
Abstract: A 3-dimensional finite-element model of slab continuous casting mould is conducted to predict the temperature of copper plates changing with thickness of copper plates and nickel layers and depth of water slots in order to clarify the effect of cooling structure on thermal behavior of copper plates. The results show that temperature distribution of hot surface is mainly governed by the cooling structure and heat-transfer conditions, and the trend of temperature distribution of transverse sections of copper plates is nearly free of cooling structure. To hot surface centricity, maximum surface temperature promotions are 30 oC and 15 oC with thickness increments of copper plates 5 mm and nickel layers 1 mm respectively and the impact of nickel layers on narrow face is slightly greater than on wide one. With 2 mm depth increments of water slots, the surface temperature without nickel layers is depressed 10 oC and with nickel layers adjacent to and away from mould outlet are depressed 7 oC and 5 oC respectively. The impact of depth of water slots on surface temperature with nickel layers is smaller than that of without nickel layers.
Key Words: slab continuous casting, mould, cooling structure, temperature of copper plates, finite element analysis
1. Introduction
In conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipates in primary cooling zone to exert enormous heating load on continuous casting mould, and thermal stress, deformation resistance and high-temperature fatigue and creep are produced to make mould life-span shorten and casting unstably. Therefore, an in-depth understanding thermal behavior of mould and analyzing the effect of cooling structure are essential to promote production operation and improve strand quality, especially to a high casting speed. Also, the cooling structure can not be reconstructed again, and its rational design is a foundation to study metallurgical process in mould.
Many studies have been carried out to shed light on thermal behavior of copper plates with high thermal load for continuous casting mould over the past years. Samarasekera and Brimacombe
[1]
mould and cast slab and offer the temperature results to be used for computing the thermo-mechanical state in the mould of thin-slab continuous casters. Also, Park et al. [3, 4] calculated the heat-flux profiles in thin-slab continuous casting moulds based on an inverse heat conduction model and mould wall temperature measured in-plant and then used them to conduct elastic-visco-plastic analysis for the different mould shapes of funnel-shaped and parallel. Lu et al
[5]
developed a solidification heat transfer model for slab casting consisting of the shell and mould domains and indicated that the thickness of the plated nickel layer and the copper plate are the most influencing factor on the mould temperature and the thickness of plated nickel should be limited. Thomas et al [6] focused on systematic study of predicting temperature, distortion and residual stress in a continuous casting mould for steel slabs and in particular to clarify that mould life is significantly affected by temperature and its rigidity, but little effect by mechanical. Liu and Zhu [7] established three-dimensional finite-element heat-transfer and thermal-stress models to predict the temperature, distortion and thermal stress in a slab continuous casting mould and analyzed the effect of copper plates thickness, water slots depth, nickel layers and casting speed on them in detail. Recently, Santillana et al [8]
calculated the
mould-wall temperature of two-dimensional longitudinal sections in billet mould and investigated the effect of cooling-water velocity, copper plates thickness and steel carbon content on temperature distribution in order to analyze the formation of rhomboidity and corner cracks. O’Connor and Dantzig [2] developed a finite-element model to analyze the temperatures in the
结晶器铜板冷却结构的优化设计_专业资料。应用数值模拟的方法,采用有限元仿真软件对某钢厂现行使用的结晶器铜板的温度场进行模拟。并在此基础上,针对结晶器铜板的...
.8×肛w (半)o.4×百1w图1Fig.1slab (3) 薄板坯结晶器铜板冷却结构示意图structure Sketchofcoolingcontinuous of copperunit plateof of thethin 式中, 中, ...
3) 结晶器冷却水强度 对铜板寿命产生影响: 结晶器内冷却要达到强制对流 传热,...机械原理与机构学 〔M. 北京:科 学技术文献出版社 .2002. 苏有良 . 平面...
万 方数据 第6期 李秀刚等:ASP连铸结晶器铜板热流和温度的研究 铜板冷面:A_O’.tm=一h。〔r(茗,=)一L〕1.3参数的确定 水缝中冷却水与铜板之间的换热...
结晶器铜板热喷涂技术的研究进展_专业资料。高作业率、高浇注速度的连铸技术要求结晶器具有高强度、高耐磨性和耐腐蚀性,热喷涂技术可达到改善其表面性能的目的。...
结晶器铜板冷却结构的优... 12人阅读 3页 2.00 连铸结晶器铜板及镀层... 建立板坯连铸结晶器三维有...
为尽量延长结晶器的使用寿命、 稳定连铸 机的操作和保证铸坯的生产质量, 必须对结晶器 铜板的材质和结构进行合理设计以确保均匀强化 冷却。在影响结晶器铜板传热...
机构整体评分:3.8 在售版权资源:7828835份 近七天成交量:12982份 进入机构... 在正常冷却条件下,结晶器内壁工作温度为250-350℃,结晶器铜板应具有良好的导热...
ASP连铸结晶器铜板热流和温度的研究_专业资料。根据在线实测的铜板温度以及ASP(Angang Strip Production)板坯连铸机冷却参数,建立了ASP板坯结晶器(高1000mm,铸坯断口...
5页 免费 ECCC-76结晶器铜板的热行为... 8页 免费 ECCC-42结晶器显示屏,一种... 7页 免费喜欢此文档的还喜欢 ECCC-55应用SOTA(state-of... 9页 免费...
热门文档