HP 光线HBA介绍
5.Save and exit.
Ignore the following message during a Red Hat Kernel ERRATA upgrade:
WARNING: No module bfa found for kernel
There is a slow-boot issue with RHEL 5.3. You can correct this by increasing the system's memory. RHEL users should change the following system ROM BIOS setting: Advanced/Remote AccessConfiguration/BIOS Remote Console = Disabled.
Installing the Brocade HCM and driver may take an excessive amount of time (30+ minutes) inlarger SAN configurations. Please be patient and wait for the process to complete.
System reboot may occasionally fail on heavily loaded SANs. Power-cycling the system shouldresolve this issue.
For SLES Linux no-arch RPM users, a known issue with Novell causes the Brocade installed driverto be overwritten by the in-box driver (1.1.0.2) when using yast2 –I to install. Check the Brocadedriver RPM version rpm –qa | grep –I bfa after using the yast2 utility to install any pack-ages. If the package is overwritten, re-installing the Brocade kit will resolve this issue.
Alternatively, the following workaround can be used to resolve the issue.
1.Launch Yast2 and select Software Management under Software
2.
3.
4.Change filter to Search and enter bfa under Search Phrase.Deselect Brocade-bfa-KMP-defaultSelect Accept and Quit.
NOTE:

This procedure applies to Brocade 1.1.0.6 and 1.1.0.8 drivers only.
There is a known issue that prevents users from updating the Brocade BIOS from the ProLiantFirmware Update CD version 8.60. For information on how to update the Brocade HBA BIOS,see the section, Performing an offline BIOS update, page 9.
The Brocade SLES 11 in-box driver may not work correctly with all HP-branded Brocade 4-Gband 8-Gb HBAs. Always use the latest drivers and DUD kits posted on the HP web-site to avoidany inconvenience.
SLES11 ReiserFS
HP and Novell are evaluating a report that ReiserFS file systems exhibit unexpected behavior underheavy loads. Other file systems, such as ext2 and ext3, are not affected by this behavior. HP
recommends that you use either the ext2 or ext3 file system. This is a high-priority issue that is beingresolved. Once a resolution is found, a maintenance update will be available on the website .
Brocade VMware drivers
The Brocade VMware drivers for version 3.5 and version 4.0 do not generate installation logs. Theinstallation process will indicate success or failure.
Important information
This section describes information you should know when installing HP-branded Brocade Fibre ChannelHBAs for ProLiant servers.
HP StorageWorks Brocade Fibre Channel host bus adapters release notes7
QuickSpecs Overview HP StorageWorks 4Gb PCIe Fibre Channel Host Bus Adapters ...1.hp.com/products/storageworks/san/documentation.html Models Brocade HP ...
Fibre Channel Host Bus Adapters brings datacenter infrastructure components to ...HP StorageWorks 8Gb PCI-e FC HBAs Models Brocade Description HP StorageWorks...
Brocade 4Gb SAN Switch for HP c-Class ...Previously, deployments using Fibre Channel-based ...HP StorageWorks Data Center Fabric Manager ...
Host Bus Adapters (HBAs): ? ? ? ? Brocade 825 Fibre Channel (FC) HBA...HP StorageWorks MSL4048 IBM 3582 Tape Library (LTO) IBM 3592-J1A ...
Fibre Channel Host Bus Adapters (HBA) Hewlett-Packard ships HP-branded ...HP StorageWorks Enterprise Backup Solution (EBS) Server Family ProLiant ...
1*10Gb级 HP Brocade 8/12 SAN Switch 1 8Gb 光纤交换机;12口可用(8个...HP QMH2572 双端口8Gb Fibre Channel Host Bus Adapter HP StorageWorks P2000 ...
Brocade 8 Gbit/sec fibre channel (FC) host bus adapters (HBAs) for IBM System x are part of a family of high-performance 8 Gbit/sec HBA solutions...
14? Supported Fibre Channel Host Bus Adapters .....16? Supported Brocade & Dell PowerConnect FOS ...Release 2 Windows Server 2008 Release 2 (with ...
verified using OEM IBM Fibre Channel adapters. ...Brocade, Emulex, and QLogic supplied drivers are ... consideration for the NetBackup 6.5.2 release....
24 See Note 1 HCL Release Revision 1.4, 19 ...Host Bus Adapters All Fibre Channel and iSCSI ...Note 12: For the HP StorageWorks Enterprise ...
热门文档