Vibration characteristics analysis of a 20-high Sendzimir mill with localized defect on the working roller
25thInternationalCongressonConditionMonitoringandDiagnosticEngineeringJournalofPhysics:ConferenceSeries364(2012)012093IOPPublishingdoi:10.1088/1742-6596/364/1/012093
intermediate rollers and the backup rollers are eliminated due to the large stiffness and slight
deflection during the rolling and to save computation time. The deformable first intermediate rollers
and the working rollers were modelled using 3D solid element SOLID164 and the thin strip was
modeled using 2D shell element SHELL163. The Coulomb friction law with a constant friction
coefficient and a critical slipping force was adopted to account for the friction process taking place
between the rollers and between the working rollers and the strip. Constant rotating speed was applied
along the center axis of the two working rollers (S) respectively. The same rolling tension force was
applied on the nodes at two edges of the strip along the rolling direction. The nodes lying at the center
line of the underneath first intermediate rollers Q and R were constrained from moving in all
directions. The decomposed rolling force according to the angle between the rollers was applied on the
nodes at the center line of the up first intermediate rollers O and P. The elastic material parameters for
the rollers are Young’s modulus E=210GPa, Poisson’s ratio ν=0.3 and density ρ= 7830kg/m3, and the
Young’s modulus for the strip is E=200GPa with same Poisson’s ratio and density.

Figure 2. The finite element model for the dynamic rolling process.
2.3. Validation of the finite element analysis
To establish confidence in the FEA program for contact problems, a three-dimensional FEA
simulation of the first intermediate roll in frictionless contact with the working roller was performed,
as shown in Figure 3. The parameters used for calculation were Young’s modulus E=210GPa and
Poisson’s ratio ν=0.3. Five different radial forces were employed for calculation as F=232.5KN,
310KN,387.5KN,465KN and 542.5KN. The results were compared with the Hertz elastic theory
[20] and are shown in Table 2. It can be seen that a difference of only 5% is found.

Figure 3. Sketch diagram of the contact deformation between rollers.
Automation and Robotics INVESTIGATIONS ON DETECTION MODEL OF LARGE SCALE ROTATION SHAFT TORSIONAL VIBRATION IN PRECISION HEAVY MACHINERY Zhao Wu School of ...
Information for papermakers Technical Assistance, Service and Know-how Press Section 8 Reduction of vibration in presses by “swinging the seam” The ...
Shock&Vibration&Drop三个测试的介绍与区别_电子/电路_工程科技_专业资料。先做 Shock, Vib, Drop 三个测试的介绍, 然后来说说区别: 一. 机构测试基本分类 1...
refers to the motion of bodies as induced by external forces DYNAMICS & MECHANICAL VIBRATIONS Basic Concept Vibration is a mass which oscillates about ...
Vibration Test_英语学习_外语学习_教育专区。PACKAGING TEST METHOD TITLE: Vibration Test Released Date: Originating Department: TCS TM No: QMKA-PACKAGING ...
Forced vibration_理学_高等教育_教育专区。受迫振动实验Forced vibration Objectives 1. Familiar with how to use the torsion pendulum to test the laws of ...
?拉格朗日方程:定义拉格朗日密度函数 L=T-U 1 Engineering Vibration, Chapter 4 §4.1 直杆的纵向自由振动 通常假设原先垂直杆件中心线的横剖面,在杆件受载...
Vibration 实验听课笔记整理我们实验时的振动实验目前主要是模拟运输过程中载具的振动对产品的破坏性。 一般 电子产品自己是不会振动的,起振动来源为载具,如汽车、...
Vibration Monitoring System - Decription and Operation_机械/仪表_工程科技_专业资料。Vibration Monitoring System - Decription and Operation...
Vibration Test_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 Vibration Test_机械/仪表_工程科技_专业资料。 ...
热门文档