The profile scanning result, using laser thickness device (Cyber Scan), is shown in figure 12.
±8[tm/cm.
Figure7. SIW filter surface scan data
Measurement and results analysis Figure 8 shows t
he appearance of the fabricated SIW filter. Vector Network Analysis (Agilent E8363B) with the fixtures done by ourselves is used to measure the filter. Figure 9 shows the principle frame. Figure 10 and figure 11 show the measurement fixture and measured results respectively.
Figurell. Measured transmission curve From the measured results, one can see that the center frequency is very similar to the simulation value (lOGHz) and the loss is a little bigger than the simulation value. The center frequency of SIW filter is decided by the shape and dimension of the metal via array on the LTCC substrate. Through measuring, there is a little difference between the dimension of the fabricated and the designed (about±20tm). From the above description, the loss of SIW is resulted from the conductor loss of the surface metal. In fact, influenced by the conductivity of the silver paste in LTCC and the surface flatness and the SMA connector, the measured value (-3--3.5dB) is a little more than the simulation result (-2.5--3dB)
Figure8. SIW filter sample
Conclusion By designing, fabricating as well as measuring of a SIW filters it was verified the feasibility of using SIW technology in LTCC. The next step is to improve the filter structure and the relative key LTCC process for developing SIW filters which can satisfy the requirements in actual applications. Passive components such as resonators, filters, power-dividers and antenna can be realized with SIW technology into LTCC which offers a new direction to integrate microwave passive components in LTCC.
VNA (Agilent E8363B) 1
M DUT
Figure9. Measurement principle frame
References 1. Piloto A, Leahy K, Flanick B, et al. Waveguide filters having a layered dielectric structure[P] . US Patent 5382931. 1995-01-17. 2. Hirokawa J, Ando M. 40 GHz parallel plate slot
FigurelO. Measurement clamp
Fund Project: Sponsored by China National Key Laboratory Fund Project (0516S051)

In this work, we propose a novel millimeter-wave SIW bandpass filter (BPF) that combines the technology of E-plane iris filter, SIW and LTCC. This ...
Keywords: Inductive post filter; Ka band; Microstrip-SIW transition; LTCC technology 1 引言 Ka波段具有许多让人注目的特点, 如高数据传 输率和良好的保密性...
本文的工作重点为利用LTCC技术的优势设计多种形 式...带状线,微带.SIW等层间互连和过渡结构进 行了仿真...WaveApplication,IEEE TheoryTech.,v01.51,no.5,...
Figure 1 LTCC structure of the X-band receiver front-end low-cost and ...vertical direction of SIW structures is developed, as illustrated in Figure ...
EMC–Filter Topology in LTCC The EMC–?lter was designed as a SIW component in LTCC. Fig. 1 depicts the simulation model of the EMC– ?lter with ...
摘要 分类号 密级 UDC 学位论文 基于SIW技术的Ka波段振荡源的研究(题名和副...The Propagation Characteristics of Substrate Integrated Waveguide Based On LTCC...
to transition of author,Waveguide-SIW-Microstrip....Thesefiltersoccupyverysmallvolume with LTCC ...in LTCC for26 GHz.IMAPS-Nordic, Stockholm,2002 ...
to—carderratioofvariouscomponentsinthesystemare analyzed.Based on these ... 微波频段LTCC埋置型带通滤波器的研究; ⑥:毫米波LTCC介质集成波导(SIW)滤波...
substrate integrated waveguide (HMSIW) for microwave application is proposed. ...SIW is shown in Figure 1, where the bottom and top planes of the sub...
[1– 4] based on LTCC and the substrate integrated waveguide (SIW) have...‘General extracted pole synthesis technique with application to low-loss TE-...
热门文档