parameters given above, with the utilization of coupling, resonance model setup in HFSS and structure tuning, the filters can be obtained and the corresponding structure and simulation results are shown as figure 3 and figure 4.
Figure3. One stage SIW filter structure
Figure4. One stage SIW filter simulation data Fabrication process of SIW filters based on LTCC technology The fabrication process, using 8 inch LTCC technical line, is shown as figure 5.
distance between vias should be more than or equal to the triple of via diameter, which is because the smaller distance between vias can lead to the bigger strain distribution between the neighboring vias and may cause-the cracks and warpage during the sintering of LTCC. In the LTCC microwave component, via with high density array is the key to the realization of electromagnetic shield. Theoretically, more dense via array can lead to the less likely occurrence of electromagnetic leap. SIW Because structure needs strong electromagnetic shield to prevent from electromagnetic leakage, the distance between vias is designed to be about twice longer than the via diameter. Some methods are used such as optimizing process parameters of via punching and adjusting the viscosity of via-filling paste and so on. The fabricated filter is observed by X-ray which is shown in figure 6, via diameter is 0.5mm and the least distance between vias of 0.8mm. From the figure 6we can see that the metal via has a round shape without the phenomenon of cracks and distortion.
Figure6. SIW filter perspective ii The metallization patterns with large area. In LTCC systems, the shrinkage of metal paste should be similar to that of LTCC green tape. The metallization patterns with large area are suggested to use mesh with the area no more than 60% for keeping the surface flatness after sintering in the current LTCC design rules. The propagation character of the SIW filter dictates its shape of metallization patterns. So some methods are used such as thinning the printing thickness of metal layers, improving isostatic pressure process parameter, optimizing co-fired curve and so on. The surface flatness of SIW filters can be as far as
Figure5. LTCC technical process
The filter used ten layers of Ferro A6M green tapes with the thickness of 0.127mm. The metal via diameter is 0.5mm. In the processing of fabricating, such technical difficulties as the followings have been solved. i High density metal vias array Base on the current LTCC design rule, the
Fund Project: Sponsored by China National Key Laboratory Fund Project (0516S051)

In this work, we propose a novel millimeter-wave SIW bandpass filter (BPF) that combines the technology of E-plane iris filter, SIW and LTCC. This ...
Keywords: Inductive post filter; Ka band; Microstrip-SIW transition; LTCC technology 1 引言 Ka波段具有许多让人注目的特点, 如高数据传 输率和良好的保密性...
本文的工作重点为利用LTCC技术的优势设计多种形 式...带状线,微带.SIW等层间互连和过渡结构进 行了仿真...WaveApplication,IEEE TheoryTech.,v01.51,no.5,...
Figure 1 LTCC structure of the X-band receiver front-end low-cost and ...vertical direction of SIW structures is developed, as illustrated in Figure ...
EMC–Filter Topology in LTCC The EMC–?lter was designed as a SIW component in LTCC. Fig. 1 depicts the simulation model of the EMC– ?lter with ...
摘要 分类号 密级 UDC 学位论文 基于SIW技术的Ka波段振荡源的研究(题名和副...The Propagation Characteristics of Substrate Integrated Waveguide Based On LTCC...
to transition of author,Waveguide-SIW-Microstrip....Thesefiltersoccupyverysmallvolume with LTCC ...in LTCC for26 GHz.IMAPS-Nordic, Stockholm,2002 ...
to—carderratioofvariouscomponentsinthesystemare analyzed.Based on these ... 微波频段LTCC埋置型带通滤波器的研究; ⑥:毫米波LTCC介质集成波导(SIW)滤波...
substrate integrated waveguide (HMSIW) for microwave application is proposed. ...SIW is shown in Figure 1, where the bottom and top planes of the sub...
[1– 4] based on LTCC and the substrate integrated waveguide (SIW) have...‘General extracted pole synthesis technique with application to low-loss TE-...
热门文档