文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 能源/化工 > TAP304_2008-10
侵权投诉

TAP304_2008-10

挪威船级社规范---钢制锻件产品型式认可规范

Standard for Certification - No. 2.9Approval Programme No. 304October 2008

5

3. Approval Documentation

This section lists the general information to be provided in theapproval application report (see section 2.3). The informationrelevant to the manufacturing of the products to be covered bythe approval of manufacturer certificate shall be submitted.The language of the submitted documentation shall be English.

—any re-heat treatment procedure to be given, if applicable—method of cleaning after heat treatment.

3.5 Special forging process approval for case hard-ened gear transmissions (if applicable)

In order to obtain approval for a “specially approved forgingprocess”, as referred in the rules Pt.4 and Classification NotesNo. 41.2, the following apply:

A detailed description of the forging process shall be given inan internal manufacturer procedure, shown to DNV, indicationat least the following parameters:

—reheating temperature and time in furnace

—the shaping operations from ingot to finished forging shall

be sketched, indicating;

—number of blows for each shaping operation—reduction ratio for each shaping operation

—typical forging temperature range for each shaping

operation

—descaling treatment during forging.

—the minimum and maximum forging ratio for the finished

forging (ingot forging) shall be given.Approval for a “special forging process” shall be combinedwith an MSA (Manufacturing Survey Arrangement) agree-ment, referring the above mentioned manufacturer proceduredescribing the approved forging process.

3.1 General Manufacturer Information

—an outline of the organisation structure including quality

control responsibilities

—manufacturing process description, visualized in flow

chart(s) indicating all process steps, and in particular theassociated testing and inspection points

—a list of the manufacturers written procedures for testing

and inspection. The procedures need not to be submitted,but must be available for review at the manufacturer’sworks upon request

—a list of equipment used for chemical analysis, mechanical

testing, metallographic examination, non-destructive test-ing and thickness measurements

—description of the qualifications of personnel engaged in

testing and inspection, including level of certification ofnon-destructive testing personnel

—procedure for product identification and traceability

(including test samples).

3.2 Product Information

A list or table specifying:—————

type of products

range of applicable product sizes and massapplicable steel types and gradesheat treatment delivery condition

reference to recognised standards or DNV rules for the ap-plicable chemical composition, mechanical properties andheat treatment

—in case raw materials for forging (slabs/ingots/etc.) are de-livered from other manufacturers; a list of raw materialsuppliers.

4. Approval Testing

4.1 General requirements

Unless otherwise specified herein, the testing procedures, testpiece shape, test piece location and orientation, and test resultsshall comply with the appropriate requirements of the RulesPt.2.

In case of newly built works, newly developed types of steel ormanufacturing processes; an increased number of forgings andforging dimensions for testing may be deemed necessary on acase by case evaluation.

In case the test results for the approval testing fails to meet therequirements given in this program and/or the rules, retestingof certain tests for the same heats is in general not permitted.However, the manufacturer shall do an evaluation of the causefor the failure and implement preventive actions. The evalua-tion report shall be submitted to DNV together with the ap-proval report. New approval testing on new heats afterimplementation of preventive actions will generally be re-quired.

Approval tests, except for determination of chemical composi-tion and metallographic examination, shall be witnessed byDNV’s surveyor. If the testing facilities are not available at theworks, the tests shall be carried out at a recognised laboratory.

3.3 Manufacturers’ own Certificate Form

Where certification of materials using the manufacturer’s owncertificate validated by DNV is intended, a blank copy of thecertificate form and a filled in certificate for a representativeproduct shall be submitted.

3.4 Information on Manufacturing Route and Equipment

3.4.1 Reheating and forging

—reheating temperature and time in furnace—forging temperature range

—type and description of forging equipment.3.4.2 Cleaning and finishing

—method of surface cleaning

—method of surplus metal removal (de-burring)3.4.3 Heat Treatment (if applicable)————

type of furnace and dimensions.heating source.

sketch indicating the positions of thermocouples

accuracy and calibration status of temperature control de-vices

—heat treatment procedures, specifying temperatures and

holding times, and where applicable, information aboutheating and cooling rates, quenching medium and coolingmedium after tempering

4.2 Test material

—Material representing forgings from two different heats

shall be tested. However, where two or more steel typesshall be covered by the approval, the testing may be re-duced to one heat per steel type

—if one steel type is subject to approval, one of the items for

approval testing should represent typical forging mass andthe other item the maximum forging mass (i.e.; at least67% of the maximum forging mass). If more than one typeof steel is subject to approval, at least one item for eachtype of steel should represent the maximum forging mass—test samples, from which test pieces are taken, shall be in-tegral with the forgings unless separately forged samplesare permitted by the Rules. Samples provided by prolon-

DET NORSKE VERITAS

上一页第5页

你可能喜欢

热门文档

相关文档

  • AISTech 2008 - FastArc technology P7-10

    AISTech 2008 - FastArc technology P7-10_冶金/矿山/地质_工程科技_专业资料...Tap to Tap 1630 (°C) Tapping Temperature Single Bucket Charge 0.7-0.8...

  • gb21671-2008测试步骤

    gb21671-2008测试步骤_计算机软件及应用_IT/计算机_专业资料。第三部分 测试... 将需要测试的网络的汇聚层至核心层交换机链路用 tap 或镜像的方式接入 ES ...

  • 多媒体技术08-09-2试卷-09040051-A

    Premiere 中,关于 Multitap Delay 音频滤镜的描述,以下___是正确的。 A.该滤镜定义整个音频素材的整个声音的质量 B.该滤镜放大音频素材的低音部分,但是使得其他...

  • FS36-350;中文规格书,Datasheet资料

    The output voltage will be either 36.0V with a center-tap under a 0....As of April 7, 2008, UL standards 506 and 1585 will be migrated to UL...

  • 预应力技术2008-3

    预应力技术2008-3_建筑/土木_工程科技_专业资料。预应力技术MCG.x.Tzj9Ok^ij...Y A}E:~pr3L8pg8/:~pgh.o r9KvzP7+8/J8cw02r*tAP 7Zth4we_8SS-E+SNLY^...

  • Zeta_Training_sc

    ACE_2008_SC_training(6... 48页 1下载券 SC...(tap water) Na4P2O7 Colloid:100ppm Minusil 10 ... k-1 = 0.304/(I)0.5 (nm) 计算离子强度 ...

  • FS20-120;中文规格书,Datasheet资料

    The output voltage will be either 20.0V with a center-tap under a 0....1 As of April 7, 2008, UL standards 506 and 1585 will be migrated to...

  • 2008WINAPN USB KEY客户端使用说明书V3.01

    2008WINAPN USB KEY客户端使用说明书V3.01_IT/计算机_专业资料。2008WINAPN ...“本地连接”的属性,如图所示 (TAP-Win32 Adapter V8) , 增加了一个“...

  • FS24-250;中文规格书,Datasheet资料

    The output voltage will be either 24.0V with a center-tap under a 0....As of April 7, 2008, UL standards 506 and 1585 will be migrated to UL...

  • FS28-040;中文规格书,Datasheet资料

    The output voltage will be either 28.0V with a center-tap under a 0....1 As of April 7, 2008, UL standards 506 and 1585 will be migrated to...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email