文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 能源/化工 > TAP304_2008-10
侵权投诉

TAP304_2008-10

挪威船级社规范---钢制锻件产品型式认可规范

4

Standard for Certification - No. 2.9

Approval Programme No. 304

October 2008

1. General

1.1 Scope

This programme gives the procedure to be followed to obtainthe Society's approval for:—steel forgings

in accordance with the requirements given in:

—DNV Rules for Classification of Ships

—DNV Rules for Classification of High Speed, Light Craft

and Naval Surface Craft—DNV Offshore Codes.

1.4 Extension or Change of Approval

An existing approval of manufacturer certificate may be ex-tended with respect to the “range of approval” as given in sec-tion 1.2.

1.4.1 Approval Documentation

For extensions or changes to the approval conditions, the ap-proval documentation specified in section 3 and already sub-mitted during the initial approval process, need not to be re-submitted. However, the documentation related to changes tothe manufacturing process shall be submitted.

1.4.2 Approval Testing

For extensions of an existing approval to include new steeltypes, additional conditions as specified in section 1.2, or sig-nificant change of maximum mass for approval (i.e. with morethan 50% of the item subject to approval testing); full approvaltesting of one heat according to section 4 is required.

1.2 Range of Approval

Approval is required for each of the following grouped typesof steel:———————

carbon and carbon-manganese,alloy,

ferritic stainless,martensitic stainless,austenitic stainless,22Cr duplex stainless,25Cr duplex stainless.

2. Approval Procedure

2.1 Application

Application for approval shall be sent to the local DNV officetogether with the following information:

—name and site address of the manufacturer.

—a list of products for which approval is requested. The list

shall include the information specified in section 1.2.—a brief description of manufacturing, testing and inspec-tion facilities and equipment.

Approval for the manufacture of one type of steel according tothe above mentioned list will cover approval of all steels with-in the same steel group. Approval for the manufacture of 25Crduplex will cover approval of 22Cr duplex.

Approval is given for a maximum forging mass. The compo-nent subjected to approval testing (see section 4) shall be rep-resentative for the maximum forging mass to be approved.Approval of the manufacturer may also be given for the fol-lowing additional conditions:

—continuous grain flow (CGF) crankshafts or crank throws;

according to DNV Classification Notes No. 41.3.

—specially approved forging process; as referred in the rules

Pt.4 and Classification Notes No. 41.2.

—clean steel forgings; according to DNV rules Pt.2.

—steel forgings for low temperature service, approved steel

grades will be given on the certificate.Steelmaking facilities, if relevant, shall be approved using ap-proval programme No. 301A.

Manufacture of forged chain cable accessories is not coveredby this program, but need separate approval according to ap-proval programme No. 311.

2.2 Works Inspection and Approval Testing

The surveyor may request additional documentation (see sec-tion 3) if deemed necessary, for his preparation for the worksinspection to be performed.

After receipt and review of the requested information the DNVsurveyor will carry out a works inspection to verify that thenecessary manufacturing, testing, and inspection facilities areavailable and supervised by qualified personnel.Approval testing shall be witnessed by DNV.

2.3 Submission of Approval Application Report

On completion of approval testing, the manufacturer shall pre-pare and submit a complete approval application report.

The approval report shall be organized in the same order andwith the same indexing as described in this program, contain-ing all the information requested in section 2.1, section 3 andsection 4. The language of the submitted documentation shallbe English.

The approval report shall be signed and dated by the manufac-turer’s representative, and sent to the local DNV office.

1.3 Validity and Renewal

The approval will be valid for four years. To maintain theapproved status, the manufacturer must be re-inspected everyfour years. Application for renewal should be made not laterthan three months before the expiry date of the certificate.Any significant alteration to the approved condition during theperiod of validity, e.g. as described in the approval documen-tation (section 3) shall be reported to the Society. A re-inspec-tion and/or re-testing may be required when deemed necessaryby the Society.

New requirements for the manufacturer due to revision of thisprogramme, i.e. imposed during the period of validity, shalltake effect at the next extension, change or renewal of the ap-proval, unless otherwise required by the Society.

2.4 Evaluation of the Approval Report

When received at the local DNV office, the approval reportshall be endorsed, that is; conforming the completeness of thereport and the correctness of the test results, by the surveyorwitnessing the tests, and forwarded to DNV Høvik for evalua-tion, together with the applicable checklists.

2.5 Issue of Approval of Manufacturer Certificate

Manufacturers whose works has been inspected and whose ap-proval documentation has been reviewed with satisfactory re-sult will be granted an “Approval of manufacturer certificate”and an entry made on DNV Exchange on the internet (doc.guandang.net).

DET NORSKE VERITAS

上一页第4页

你可能喜欢

热门文档

相关文档

  • AISTech 2008 - FastArc technology P7-10

    AISTech 2008 - FastArc technology P7-10_冶金/矿山/地质_工程科技_专业资料...Tap to Tap 1630 (°C) Tapping Temperature Single Bucket Charge 0.7-0.8...

  • gb21671-2008测试步骤

    gb21671-2008测试步骤_计算机软件及应用_IT/计算机_专业资料。第三部分 测试... 将需要测试的网络的汇聚层至核心层交换机链路用 tap 或镜像的方式接入 ES ...

  • 多媒体技术08-09-2试卷-09040051-A

    Premiere 中,关于 Multitap Delay 音频滤镜的描述,以下___是正确的。 A.该滤镜定义整个音频素材的整个声音的质量 B.该滤镜放大音频素材的低音部分,但是使得其他...

  • FS36-350;中文规格书,Datasheet资料

    The output voltage will be either 36.0V with a center-tap under a 0....As of April 7, 2008, UL standards 506 and 1585 will be migrated to UL...

  • 预应力技术2008-3

    预应力技术2008-3_建筑/土木_工程科技_专业资料。预应力技术MCG.x.Tzj9Ok^ij...Y A}E:~pr3L8pg8/:~pgh.o r9KvzP7+8/J8cw02r*tAP 7Zth4we_8SS-E+SNLY^...

  • Zeta_Training_sc

    ACE_2008_SC_training(6... 48页 1下载券 SC...(tap water) Na4P2O7 Colloid:100ppm Minusil 10 ... k-1 = 0.304/(I)0.5 (nm) 计算离子强度 ...

  • FS20-120;中文规格书,Datasheet资料

    The output voltage will be either 20.0V with a center-tap under a 0....1 As of April 7, 2008, UL standards 506 and 1585 will be migrated to...

  • 2008WINAPN USB KEY客户端使用说明书V3.01

    2008WINAPN USB KEY客户端使用说明书V3.01_IT/计算机_专业资料。2008WINAPN ...“本地连接”的属性,如图所示 (TAP-Win32 Adapter V8) , 增加了一个“...

  • FS24-250;中文规格书,Datasheet资料

    The output voltage will be either 24.0V with a center-tap under a 0....As of April 7, 2008, UL standards 506 and 1585 will be migrated to UL...

  • FS28-040;中文规格书,Datasheet资料

    The output voltage will be either 28.0V with a center-tap under a 0....1 As of April 7, 2008, UL standards 506 and 1585 will be migrated to...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email