DEUTSCHE NORM ~~~
SeDtember 1996
Rotary shaft lip seals
DIN
3760 Supersedes April 1972 edition
ICs 21.120.10 Descriptors: Fluid power, lip seals. Radial-Wellendichtringe
In keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker.
Foreword This standard has been prepared by the Normenausschuß Kautschuktechnik (Rubber Technology Standards Committee). It is based on IS0 6194-1: 1982. Amendments The following amendments have been made to the April 1972 edition. a) For shaft diameters 32, 35, 38 and 40 mm, a nominal width of 8 mm has been introduced to account for new designs. b) Information to be provided by both the manufacturer and the purchaser has been included. c) The standard has been editorially revised. Previo us edit ions DIN 3760: 1962-02, 1972-04.
Dimensions in mm
1 Scope and field of application This standard specifies dimensions and requirements for materials, marking, use and installation of rotary shaft lip seals used for retaining fluid or grease in unpressurized equipment, or equipment with a low differential pressure, that has rotating shafts. Where seals are intended for use in applications other than those specified in this standard, the seal manufacturer should be consulted.
2
Normative references
This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. DIN 51 524-1 Type HL hydraulic oils - Minimum requirements DIN 51 524-2 Type HLP hydraulic oils - Minimum requirements DIN 51524-3 Type HVLP hydraulic oils - Minimum requirements IS0 1629: 1995 Rubbers and latices - Nomenclature IS0 4287-1: 1984 Surface roughness - Terminology - Part 1: Surface and its parameters IS0 61 94-1: 1982 Rotary shaft lip type seals - Part 1: Nominal dimensions and tolerances
Continued on pages 2 to 13
Translation by DI N-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text.
No pari of this translation may be reproduced without the prior permission of V Deutsches Institut für N o n u n g e. V., Berlin. Luth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen).
Ref. No.~- 3760: 1996-0 DIN ...~ ~
English price group O9
Sales No.o109 08.98
doc.guandang.net

oay flye l-Nmiahip e “179B123-8 dmesos d lrne ininanteacso 本标准等效采用国际标准IO9/-18《 S64192旋转轴唇形密封圈— 第11 部分: 基本尺寸和公差》 ...
旋转轴唇形密封圈研究浅探_化学_自然科学_专业资料。今日推荐 157份文档 ... DIN 3760-1996 ENG旋转... 13页 1下载券喜欢此文档的还喜欢...
旋转轴唇形密封圈的结构_专业资料。旋转轴唇形密封圈通常称为油封,本文介绍了油封机理和油封结构的优缺点。旋转轴唇形密封圈的结构及优点旋转轴唇形密封圈通常称为...
旋转轴唇形密封圈规格表_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 旋转轴唇形密封圈规格表_机械/仪表_工程科技_专业资料。 ...
GB-T98771-1988内包骨架旋转轴唇形密封圈_建筑/土木_工程科技_专业资料。GB-T98771-1988内包骨架旋转轴唇形密封圈免责声明 GB-T9877.1-1988内包骨架旋转轴...
旋转轴唇形密封圈_机械/仪表_工程科技_专业资料。旋转轴唇形密封圈旋转轴唇形密封圈 1,旋转轴唇形密封圈使用工况及场合 拥有氟胶,硅胶,丁腈胶类产品,广泛应用于...
旋转轴唇形密封圈压装套的典型结构_专业资料。在各种机械类产品、设备中,广泛使用旋转轴唇形密封圈,用于对各种油液、润滑脂或其他液体起到密封作用。唇形密封圈的...
旋转轴唇形密封圈的设计与选材_专业资料。详细叙述了旋转轴唇形密封圈的密封机理,影响因素,设计结构要点及材料选取原则。第3 1卷第 5期 210 0年1 O月 特种...
1 14 DOI:10.11832/j.issn.1000-4858.2013.05.032 液压与 气动 201 3年第 5期 〕J 旋转轴唇形密封圉的有限元分析与仿真 桑建兵 , 邢素芳 , 刘宝会 ...
热门文档