铸造数值模拟
Simulation of the Solidification Parameters of Single Crystal Casting
H.P. Jin1, a, J.R. Li1,b and S.Z. Liu1,c
1
National Key Laboratory of Advanced High Temperature Structural Materials,
a
Beijing Institute of Aeronautical Materials, P.O. Box 81-1, Beijing 100095, China
jhp9@yahoo.cn, bjiarong.li@biam.ac.cn, cshizhong.liu@biam.ac.cn
Keywords: Single crystal superalloy castings, Numerical simulation, Solidification parameters
Abstract. The effects of thermal physical parameters and boundary conditions on investment solidification parameters were obtained using a computer simulation system. Directional solidification parameters of single crystal superalloy include the temperature distribution, the position and the shape of the solid/liquid interface in the mushy zone of the solidifying blade casting. Commercial finite-element analysis software, ProCAST, was used to simulate the solidification processes of the castings of single crystal DD6. The simulation results indicate that the predictions of the temperature show little sensitivity to the thermal physical parameters and boundary conditions. Further, it has also been shown that the location and the shape of solid/liquid interface is related to the boundary conditions of simulation. Increasing the value of interface heat transfer coefficient decreases the width of mushy zone. Introduction
Nickel-based single crystal superalloys are predominately used as materials for turbine blades in aero-engines because of their excellent mechanical properties at elevated temperatures. Turbine blades are usually produced by investment casting. The design and optimizations of investment cast processes for single crystal castings have involved a great of expensive experiments. Although the casting technology of advanced gas turbine blades have been improved by trail and error in the past, numerical simulation is an effective and powerful tool to provide much insight into the mechanism of the directional solidification fundamental and the formation of deleterious casting defects. At the same time, there are many parameters involved in the investment process simulation for single crystal superalloy and most of them are hard to measure or even impossible. Accurate thermophysical data and boundary conditions are difficult to obtain at high temperatures, especially for reactive alloys such as titanium and nickel-based superalloys [1]. These characteristics make the prediction of directional solidification more difficult.
Some effort has been expanded in this direction recently. For binary alloy [2], interface heat transfer coefficients increase will result in temperature gradient improvement along with the heat-extracted direction. The convection decreases with the increasing of the density. As for CMSX-4 single crystal superalloy [3,4], the temperature prediction and thermal gradient in the liquid are the most sensitive to the accuracy of the values used for density and thermal conductivity in the solid. Thermal conductivity in the liquid, specific heat and density have similar levels of influence on solidification time; thermal conductivity in the solid has the opposite effect compared to all the other properties studied. However, the magnitude of this change is small. Altering the conductivity by 15% only changes the solidification time by 4%. Philippe [5] investigated the effects of geometry size and withdrawal speed on the mushy zone isotherms in the middle of the steady-state solidification of the casting using numerical simulation methods. Several qualitative observations drew, faster withdrawal speeds results in shallower thermal gradients. And the various withdrawal speeds only affect the position of the growth front relative to the baffle. The interface was noticeably more sensitive to curvature for large casting sizes.
In this paper, single crystal superalloy DD6 was chosen as the base alloy to investigate the influence of thermal physical parameters and boundary conditions on the solidification process
Numerical Simulation of Solidification Process on Single Crystal Ni-Based Superalloy Investment_专业资料。维普资讯 http://www.cqvip.com J.Mae.Sitrc.Tehn....
Numerical simulation of solidification morphologies of Cu-0.6Cr casting alloy using modified cel_专业资料。翟 Avibeolea all ni tanwww.cecdrc.o sineitcren...
Non-Metallic Inclusion during Solidification of ... France % % Abstract A numerical simulation which...studied the in?uence of di?erent parameters like...
Numerical simulation of solidification and liquation behavior during welding of low-expansion s_专业资料。 Sa—igG t1hoQn UOea .Nurasli foiictnadlutnbh...
+simulation+of+moldtemperaturecontrol+solidification_...of the forming state and control parameters for ...crystal quality and obtain columnar crystals of ...
Numerical simulation of mold-temperature-control solidification_专业资料。维普资讯 http://www.cqvip.com Avibeoniea all l tanwww.cecdic.om sinertecS ...
EPFL COMBINATION OF PARAMETERS CHARACTERISTIC FOR MICROSTRUCTURES & PROCESSING MICROSTRUCTURE-PROCESSING MAP EPFL PROCESSING-MICROSTRUCTURE MAP Solidification Velocity...
Simulation of the Entire Crystal Growth Process: ...(solidification front, melt/gas interface including...Additional parameters can be introduced to ...
parameters (heater power, crystal pulling rate, ...dependent simulation of the Cz process has become...of the solidification front, and of the dynamic ...
In the present work ,Nickel-based single crystal superalloy were chosen as ...of the boron content to solidification parameters of alloys.There are some ...
热门文档