SC70, Single/Dual Low-Voltage, Low-Power µP Reset CircuitsMAX6381–MAX6390
Detailed Description
RESET Output
A µP reset input starts the µP in a known state. TheseµP supervisory circuits assert reset to prevent codeexecution errors during power-up, power-down, orbrownout conditions.
Reset asserts when VCCis below the reset threshold;once VCCexceeds the reset threshold, an internal timerkeeps the reset output asserted for the reset timeoutperiod. After this interval, reset output deasserts. Resetoutput is guaranteed to be in the correct logic state forVCC≥1V.
Manual Reset Input (MAX6384/MAX6385/MAX6386/MAX6390)
Many µP-based products require manual reset capabil-ity, allowing the operator, a test technician, or externallogic circuitry to initiate a reset. A logic low on MRasserts reset. Reset remains asserted while MRis low,and for the reset active timeout period (tRP) after MRreturns high. This input has an internal 63k pullupresistor (1.35k for MAX6390), so it can be left uncon-nected if it is not used. MRcan be driven with TTL orCMOS logic levels, or with open-drain/collector outputs.Connect a normally open momentary switch from MRtoGND to create a manual-reset function; externaldebounce circuitry is not required. If MRis driven fromlong cables or if the device is used in a noisy environ-ment, connecting a 0.1µF capacitor from MRto GNDprovides additional noise immunity.
RESET IN Comparator
(MAX6387/MAX6388/MAX6389)
RESET IN is compared to an internal +1.27V reference.If the voltage at RESET IN is less than 1.27V, resetasserts. Use the RESET IN comparator as a user-adjustable reset detector or as a secondary power-sup-ply monitor by implementing a resistor-divider at RESETIN (shown in Figure 1). Reset asserts when either VCCor RESET IN falls below its respective threshold volt-age. Use the following equation to set the threshold:
VINTH= VTHRST (R1/R2 + 1)where VTHRST= +1.27V. To simplify the resistor selec-tion, choose a value of R2 and calculate R1:
R1 = R2 [(VINTH/VTHRST) - 1]
Since the input current at RESET IN is 50nA (max),large values can be used for R2 with no significant lossin accuracy.
___________Applications Information
In addition to issuing a reset to the µP during power-up,power-down, and brownout conditions, theMAX6381–MAX6390 are relatively immune to short dura-tion negative-going VCCtransients (glitches).
The Typical Operating Characteristicssection shows theMaximum Transient Durations vs. Reset ComparatorOverdrive, for which the MAX6381–MAX6390 do notgenerate a reset pulse. This graph was generated using

Negative-Going VCCTransients
6_______________________________________________________________________________________
MAX6387XS16D5-T中文资料 隐藏>> 元器件交易网www.cecb2b.com 19-1839; Rev...(MAX6384/MAX6385/MAX6386) o Auxiliary RESET IN (MAX6387/MAX6388/MAX6389...
MAX6387XS16D5-T中文资料 隐藏>> 元器件交易网www.cecb2b.com 19-1839; Rev...MAX6385 MAX6388 MAX689 MAX6383 MAX6390 MAX6381–MAX6390 1 (MAX6382/ MAX...
VTH/°C VCC falling at 10mV/?s from VTH + 100mV to VTH - 100mV D1 D2 Reset Timeout Period MAX6381–MAX6389 (See Reset Timeout table) D3 ...
MAX6389XS16D5-T中文资料 隐藏>> 元器件交易网www.cecb2b.com 19-1839; Rev...MAX6385 MAX6388 MAX689 MAX6383 MAX6390 MAX6381–MAX6390 1 (MAX6382/ MAX...
MAX6389XS16D5-T中文资料 隐藏>> 元器件交易网www.cecb2b.com 19-1839; Rev...(MAX6384/MAX6385/MAX6386) o Auxiliary RESET IN (MAX6387/MAX6388/MAX6389...
MAX6386XS16D5中文资料 暂无评价 13页 免费 TBA820M-D08-T中文资料 5页 ...Auxiliary RESET IN (MAX6387/MAX6388/MAX6389) ? VCC Reset Timeout (1120ms...
MAX6388XS16D1中文资料 暂无评价 13页 免费 TBA820M-D08-T中文资料 5页 ... MAX6388XS16D1-T中文资料 隐藏>> 元器件交易网www.cecb2b.com 19-1839; Rev...
MAX6388XS16D3中文资料 暂无评价 13页 免费 MAX6388XS16D3+中文资料 暂无评价 ...VCC V ms ms TYP MAX 5.5 13 11 7 6 VTH + 1.5% V VTH + 2.5%...
VTH/°C VCC falling at 10mV/?s from VTH + 100mV to VTH - 100mV D1 D2 Reset Timeout Period MAX6381–MAX6389 (See Reset Timeout table) D3 ...
热门文档