文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > AMS 2759-9D-2009 钢制零件的除氢
侵权投诉

AMS 2759-9D-2009 钢制零件的除氢

原文

AMS 2759-9D-2009 钢制零件的除氢

AEROSPACE MATERIAL

SPECIFICATION

RATIONALE

AMS2759/9D

Issued 1996-11 Revised 2009-05

Superseding AMS2759/9C

Hydrogen Embrittlement Relief (Baking) of Steel Parts

AMS2759/9D was issued to correct a publishing error in 3.3.3.6: “four” is returned to “24” hours. 1. SCOPE 1.1 Purpose

This specification covers the requirements for embrittlement relief (baking) of heat treated steel parts to remove hydrogen infused during plating and certain other chemical processing such as stripping, chemical milling, pickling, and etching. 1.2 Application

This specification is applicable to parts made from carbon, low-alloy, and martensitic stainless steel heat treated to a minimum strength of 180 ksi (1241 MPa) or heat treated to a minimum hardness of 40 HRC or equivalent. It is also applicable to threaded fasteners made from carbon, low-alloy, or martensitic stainless steels heat treated to a minimum strength of 150 ksi (1034 MPa) or 34 HRC or equivalent, parts made from high strength precipitation hardening stainless steels other than A-286, and steel parts which have been case hardened (carburized, nitrided, nitrocarburized, or carbonitrided). See 8.2.

2. APPLICABLE DOCUMENTS

The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications

Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), doc.guandang.net. AMS2649 Etch Inspection of High Strength Steel Parts AMS2750 Pyrometry AMS2759 Heat Treatment of Steel Parts

__________________________________________________________________________________________________________________________________________ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright © 2009 SAE International

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) SAE values your input. To provide feedback

第1页

你可能喜欢

热门文档

相关文档

  • AMS2759-5D中文版

    AMS2759-5D中文版_机械/仪表_工程科技_专业资料。马氏体不锈钢零件的热处理 1. 范围 本规范连同 AMS 2759 中提及的钢的热处理的一般要求一起, 构成了马氏体 ...

  • AMS5703D

    AMS 2759-9D-2009 钢制零件... 5页 5财富值 SAE AMS 5732J-2006 固溶热... 7页 10财富值 AMS H-6875A美国的军用热处... 29页 5财富值 AMS_5630G...

  • AMS2759

    AMS2759_交通运输_工程科技_专业资料。AEROSPACE MATERIAL SPECIFICATION AMS 2759... AMS2759-9D 5页 1下载券 AMS2759-1E 13页 1下载券 AMS2759-8A 13页 1...

  • AMS2759-3E

    AMS2759-3E_机械/仪表_工程科技_专业资料。美国国家标准今日推荐 ... AMS2759-2E AMS2759-5D AMS2759-8A AMS2759-9D AMS2759-9c1/2 相关文档...

  • AMS 2759-9

    AEROSPACE MATERIAL SPECIFICATION AMS 2759/9B Issued Revised NOV 1996 APR 2003... AMS 2759-7A 15页 1下载券 AMS 2759-9D-2009 钢制零... 5页 2下载券 ...

  • AMS2759-1E

    AMS2759-1E_机械/仪表_工程科技_专业资料。美国国家标准今日推荐 ... AMS2759-2E AMS2759-3E AMS2759-5D AMS2759-8A AMS2759-9D AMS2759-9c ...

  • AMS-H-6875A-V2

    环境 气态/燃烧废气 氩 3/ 氦 3/ 氢 3/ 氮 ...本文档零部件的任何参照被 AMS 2759 的相应要求取代...B 和 D 钢制热处理材料的硬度检测:最终热处理后的...

  • AMS2759-8A

    AMS2759-9D 5页 1下载券 AMS2759-5D 11页 1下载券 AMS2759-9c 5页 1下载券 AMS2759-5D中文版 8页 2下载券 AMS2759-3E 15页 1下载券 喜欢此文档的...

  • AMS2759-11

    AMS2759-11_机械/仪表_工程科技_专业资料。美国国家标准今日推荐 ... AMS2759-9D 5页 1下载券 AMS2759_2F 暂无评价 13页 1下载券 AMS2759-5D...

  • AMS 2759宇航材料规范

    2 AMS 2759/3C 3.3.1 果热处 ℉(774 热处理环境: 零件必须在空气中或保护气氛中热处理, 可接受的保护气氛包括氩、 氦、氢中性盐和真空。氮和氮氢混和物...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email