485电路介绍
Jan Axelson

RS-485 is often the interface of choice.The network nodes can be PCs,microcontrollers, or any devices capableof asynchronous serial communications.Compared to Ethernet and other net-work interfaces, RS-485’s hardwareand protocol requirements are simplerand cheaper.
The RS-485 standard is flexibleenough to provide a choice of drivers,receivers, and other components de-pending on the cable length, data rate,number of nodes, and the need toconserve power.
Several vendors offer RS-485 trans-ceivers with various combinations offeatures. Also, there are options formethods of terminating and biasingthe line and controlling the driver-enable inputs.
In this article, I show you severalcircuits for RS-485 networks. Even if
20 Issue 107 June 1999
CIRCUIT CELLAR®
you use prebuilt cards or converters,understanding the options will helpyou choose the right product and
configure it to get the best results foryour application.
RS-485 IN BRIEF
But first, a quick look at RS-485.The interface popularly known as RS-485 is an electrical specification formultipoint systems that use balancedlines. RS-485 is similar to RS-422, butRS-422 allows just one driver withmultiple receivers whereas RS-485supports multiple drivers and receivers.The specification document (TIA/EIA-485-A) defines the electrical char-acteristics of the line and its driversand receivers. There are brief sugges-tions relating to terminations andwiring, but there’s no discussion ofconnector pinouts or software proto-cols (as there is for RS-232).
An RS-485 network can have up to32 unit loads, with one unit load equiva-lent to an input impedance of 12k. Byusing high-impedance receivers, youcan have as many as 256 nodes.
An RS-485 link can extend as far as4000′ and can transfer data at up to10 Mbps, but not both at the sametime. At 90 kbps, the maximum cablelength is 4000′, at 1 Mbps it drops to400′, and at 10 Mbps it drops to 50′.For more nodes or long distances, youcan use repeaters that regenerate thesignals and begin a new RS-485 line.Although the RS-485 standard saysnothing about protocols, most RS-485links use the familiar asynchronousprotocols supported by the UARTs inPCs and other computers. A transmittedword consists of a start bit followed bydata bits, an optional parity bit, and astop bit.
Two ways to add RS-485 to a PCare on an expansion card and by at-taching an RS-485 converter to anexisting port. Converters for RS-232are widely available and Inside OutNetworks has developed a USB–to–RS-485 converter, also available fromB&B Electronics. On microcontrollers,you can connect an RS-485 transceiver
doc.guandang.net
Designing


RS-485 Circuits
RS485串行通信电路的设计_电子/电路_工程科技_专业资料。RS485 串行通信接口电路的总体设计 在电参数仪的设计中,数据采集由单片机 AT89C52 负责,上位 PC 机主要...
RS485硬件电路设计中需注意的问题_电子/电路_工程科技_专业资料。RS485硬件电路设计中需注意的问题RS48 硬件电路设计中需注意的问题 1 问题的提出在工业控制及...
在使用 RS-485 总线时,如果简单地按常规方式设计电路,在实际工程中可能有以下两个问 题出现.一是通信数据收发的可靠性问题;二是在多机通信方式下,一个节点的...
RS232/RS485转换电路设计_电子/电路_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 RS232/RS485转换电路设计_电子/电路_工程科技_专业资料。第3 卷第...
485电路设计_信息与通信_工程科技_专业资料。电路设计485 通信 2009-02-10 10:25 图 1. RS-485 系统示意图 由于实际应用系统中,往往分散控制单元数量较多,...
科技信息 计算机与网络 RS485远程通信电路系统设计广西大学电气工程学院广西玉林师范学院余旺新〔摘要〕RS485采用平衡发送和差分接收,具有抑制共模干扰的能力。加上总线...
RS485EMC设计标准电路_电子/电路_工程科技_专业资料。RS485EMC电路5 4 3 2 1 D 备注 1.此电路为户外环境使用,具有较高的防护能力, 当使用环境变化时,可以...
RS485光耦应用电路图_电子/电路_工程科技_专业资料。RS485 RS485应用电路图最...电路设计中可以考虑采用高速光耦,如6N137、6N136等芯片,也可以优 化普 通光耦...
RS485硬件电路分析 RS485接口定义描述 1 RS485接口定义描述 1.1 简介 1.2 RS485特点 RS485电路设计 2 RS485电路设计 2.1 2.2 2.3 2.4 2.5 2.6 ...
RS485光耦应用电路图_电子/电路_工程科技_专业资料。RS485 RS485应用电路图最...电路设计中可以考虑采用高速光耦,如6N137、6N136等芯片,也可以优 化普 通光耦...
热门文档