文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 人文社科 > 哲学/历史 > 06 wire bond loop profile development for fine pitch-long wire assembly
侵权投诉

06 wire bond loop profile development for fine pitch-long wire assembly

394

IEEE TRANSACTIONS ON SEMICONDUCTOR MANUFACTURING, VOL. I, NO. 3, AUGUST 1994

I I

I

’ I0.006’

X

1 Low loop height On tOD O f bond ball Moderate loop height to mlnlmlze w i r e length and w i r e sweep

0.0045-

SlDF V l F W Fig. 1. Front view and side view of a wire and a capillary on a 4.5 mil pad pitch die. TABLE I CENTRAL COMPOSITE DESIGN OF

EXPERIMENT LF (%o)

RUN# 1

Stralght wire to mlnlmlze w i r e length and w i r e sweep

Fig. 2. The“ideal” loop profile for a 150 mil gold wire. DeJnition f o r Loop Profile Characterization Points[2]: Point A through L are shown in Fig. 4 and their significance is defined below. Point A ( X# 0.65,Z) is the point where the wire starts to deviate from perpendicularity off the origin. The positions of point A and point B can give an indication of the stress stored in the neck of the ball bond. Point B ( X= min ., 2 ) is the point at which the wire is at its furthest distance from the second bond. As stated above point B can add greatly to the stress stored in the neck of the ball bond especially as it deviates further from perpendicularity. Point C is not detailed in Fig. 4.Its location can be seen in Fig. 3. Point D ( X, Z= max.) is the highest point of the loop. The higher point D is, the more likely wire sweep will occur during the plastic encapsulation process. Point E (0,Z) is perpendicular to the origin. Point E is the most likely point the capillary will contact as it is bonding the adjacent pad. Therefore control of point E in the bonding operation is critical. If point E is too high the probability of wire damage is very high. Point F ( X,Z= min .) is the lowest point of the wire. Excessive wire sag can lead to shorts to the die edge or to the die attach pad edge. Point G ( X,5), I

(X, 5), J(X, 0 ), K(X, -5), and L(X, -10) define wire locations at Z equal 5,0, -5, and -10 mil, respectively. They were used to estimate the straightness of the wire between points D

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 I9 20 21 22 23 24 25

KH (mil) 6 9 6 9 6 9 6 9 6 9 6 9 6 9 6 9 5 10 8 8 8 8 8 8 8

RL (”0) 94 94 131 131 94 94 131 131 94 94 131 131 94 94 131 131 113 113 75 150 113 113 113 113 113

94 94 94 94 131 131 131 131 94 94 94 94 131 131 131 131 113 113 1 I3 113 75 150 113 113 113

VAC (psi) 3 3 3 3 3 3 3 3 8 8 8 8 8 8 8 8

5 5 5 5 5 5 0 10

5

and F. Point H ( X,10) was defined but does not occur in every run in actual measurements. Therefore, point H was not used. In addition total wire length (TWL) can be calculated from the sum of the length of all of the sections. Wire sway (SW) can also be determined with the data collected (See Fig. 5 . )

1 1 RESULTS 1. AND DISCUSSIONS Least Square Regression Results: Table I1 summarizes the least square regression coefficients and the corresponding correlation coefficients for each loop profile characterization point.

06 wire bond loop profile development for fine pitch-long wire assembly

上一页第2页

你可能喜欢

热门文档

相关文档

  • WIRE BOND PROCESS INTRODUCTION(金线邦定过程介绍)

    WIRE BOND PROCESS INTRODUCTION CONTENTS ASSEMBLY ...Multimode Transducer System Programmable profile, ...Bond Pad Pitch Ball Size Ball Thickness Loop ...

  • Wire Bond Training

    ASSEMBLY FLOW OF CIS ? Wire Bond Theory ? M/...2.5 um ?Fine Pitch Capability ?35 mm pitch @...loop Prepared pad By Hawk Long Source:NA Camtech...

  • Finepitch

    Capillary interferes with 1st bond ? Used cap (PBGA 45um) with profile ... New Generation 4N wire for super-long loop, for fine pad pitch (Flex ...

  • Spec_Wire-Bond-Inspection-Tools

    file://C:\Wire-Bond-Inspection-Tools.html 9/17/03 Assembly - Wire ...D. Use the Fine/Coarse focus knobs to bring the top of the wire loop ...

  • K&S looping mode J-Wire

    Loop J-Wire II RF Loop II Security Bond II ...Long Wire, Fine Pitch, QFP, PLCC, SOJ, LOC,...J-Wire Loop Profile J-Wire GUI Screens Following...

  • wire bond - Bond modes

    UL loop ? by ESEC February 2004, High ...Assembly Solutions 10 CONFIDENTIAL Bond modes - IF...s due to small capillary IC ( fine pitch ) ?...

  • 一种基于图像分析的引线曲率测量算法研究

    Wire Bond Loop Profile Development for Fine Pitch -Long Wire Assembly [J]...系统仿真学报,2006,18(11): 3058-3062。 作者简介 :周洪军(1985-),男,硕士...

  • Wire Bonding process

    PROFILE Z-axis EFO Ball bond Looping Search wedge Wedge bond Search ball ...long loop bonding Low temperature bonding Fine pitch / fine size bonding ...

  • ASM焊线(wire bond)摆线探索

    ASM焊线(wire bond)摆线探索_机械/仪表_工程科技_专业资料。ASM焊线工艺探索...3 kink 的 loop profile 昨天用 BGA-last loop 打出来 的效果如左图, 这是...

  • ...Bond Enhancement For X-Wire Insulated Bonding Wi...

    Stitch Bond Enhancement For X-Wire Insulated ...assembly process flow, with minimal capital ... Fine Pitch Copper Wire... 8页 免费 Wire ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email