文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > A Kalman-Filter Method for Power Control in Broadband Wireless Networks Abstract A Kalman-f
侵权投诉

A Kalman-Filter Method for Power Control in Broadband Wireless Networks Abstract A Kalman-f

method for power control is proposed for broadband, packet-switched TDMA wireless networks. By observing the temporal correlation of cochannel interference when transmitters can send data contiguously, a Kalman filter is used to predict interfence power in

time slots) varies randomly from message to message.Despite such randomness, the networks allow multiple,contiguous time slots to be used by the same terminal orbase station for transmitting a message. As a consequence,the interference at a given receiver is correlated from onetime slot to the next. We observe that suchtemporalcorrelationfor the interference becomes strong quicklywhen the message length increases from one. For thisreason, based on the interference measurements inprevious slots, one can apply appropriate methods topredict the interference power to be received at a terminalor base station in the next time slot. Based on thepredicted interference and estimated path gain between thetransmitter and receiver, the transmission power in the nexttime slot can be determined to achieve the desiredperformance in terms ofsignal-to-interference-plus-noiseratio(SINR). These are the key ideas behind the powercontrol algorithm proposed in the following.

In particular, we propose to use a Kalman lter [BH97][H96] to predict the interference power, thus our powercontrol algorithm is referred to as theKalman- ltermethod.The advantage of the Kalman lter is that it issimple due to its recursive structure and robust over a widerange of parameters and conditions, and possibly providesan optimal estimate with minimum mean square error. Itis well known that Kalman lter has been appliedsuccessfully to many systems [BH97]. As for wirelessnetwork applications, [DJM96] proposes using a Kalman lter for call admission in CDMA networks. We reporthere that Kalman ltering is also useful in controllingtransmission power in TDMA networks.

To understand why power control can be crucial in thedesign of broadband TDMA networks, especially for lowfrequency reuse factor, let us consider a 4-sector cellularsystem with the (static)interleaved channel assignment(ICA) proposed in [WL98], as shown in Figure 1. In thislayout, each cell is divided into four sectors and eachsector is served by a 60oantenna. In the ICA scheme,each cell in the same column is assigned four channels (orchannel sets), one for each of its four sectors. To take fulladvantage of the directivity of sectoral antennas, thechannels assigned to the corresponding sectors of adjacentcells in the same column are interleaved. For example,channel 1 and 2 are assigned to the upper-left sectors in themiddle column of cells in Figure 1 in an interleavedfashion; these channels are assigned the upper-right sectorsof the cells in the same way. Similarly, channel 3 and 4are assigned to the lower-left and lower-right sectorsinterleavingly in the same cell column. The assignment inthis gure allows cells in a neighboring column to use adifferent set of four channels, thus the assignment yields afrequency reuse factor of 2/8 (i.e., a channel is reused inevery two cells and in every eight sectors). Usingsimulation techniques with reasonable assumptions andtypical radio parameters (see Section 5 for details), Table 1presents SINR percentiles for the uplink under variouspower control schemes in the system in Figure 1. Notethat full power control adjusts the transmission power tofully compensate for the path loss and shadow fading from

a terminal to its base station, while the optimal powercontrol (without considering thermal noise) is the methodby [GVG94], which maximizes the minimum SIR amongall links by balancing the transmission power. As shownin the table, comparing with no power control, aperformance improvement of as much as 10dB can beachieved when the optimal control is employed. This largepotential performance gain has motivated us to devise anappropriate power control scheme with a hope ofachieving performance as close to the optimal as possible.The organization of the rest of this paper is as follows.In section 3, the Kalman- lter method for power control ispresented. The theoretical basis of the new method isdiscussed in Section 4. Then, in Section 5, we usesimulation techniques to study the performance of the newmethod for the system shown in Figure 1. In addition, wealso explain and interpret the numerical results. Finally,we present our conclusions and future work in Section 6.3. A KALMAN-FILTER METHOD FOR POWERCONTROLAlthough the Kalman- lter method for power controlis applicable to both uplink (from terminal to base station)and downlink (from base station to terminal), ourdiscussion will focus on the uplink here.3.1 System Assumptions

1. Given that a terminal and its base station

communicate directly with each other, we assumethat the path gain between them (e.g., the sum of thepath loss and shadow fading for the radio link) canbe estimated accurately by measurements. This is areasonable assumption, especially for the linkquality not changing much in time when the terminalis moving at a very slow speed or stationary.2. The multi-access control (MAC) protocol in use

allows at most one terminal in each sector or cell tosend data at a time; that is, no data contention occurswithin the same sector or cell. In addition, the basestation knows which terminal is scheduled totransmit at different times. (Both requirements canbe achieved by using, for example, polling schemesas the MAC protocol. Having data contention in thesame sector or cell will further complicate the powercontrol problem as the interference power uctuateseven more, depending on whether or not more thanone terminals transmit concurrently in a sector orcell.) When a terminal is permitted to transmit, it cansend packets in multiple time slots contiguously.3. Due to large volume of data involved, base stations

cannot exchange information among themselves ona per packet basis in real time. Thus, it is extremelydif cult to estimate how much interference onetransmission causes to others in neighboring cells.4. Interference power in each time slot can be

measured quickly but possibly with noise and errorsat each base station. At a high level, the interferencepower is equal to the difference between the total

上一页第2页

你可能喜欢

热门文档

相关文档

  • Kalman Filter 的C实现

    (0); //initialize with a measurement x_est_last = z_real + frand()*0.09; float sum_error_kalman = 0; float sum_error_measure = 0; for (...

  • kalman滤波程序

    % [x, V, VV, loglik] = kalman_filter(y, A, C, Q, R, init_x, init_V, ...) % % INPUTS: % y(:,t) - the observation at time t % ...

  • Kalman滤波

    源于1957年他在哥伦比亚大学的一篇博士 论文和1960年发表的论文《A New Approach to Linear Filtering and Prediction Problems》,60年代Kalman 把状态空间模型引入滤波...

  • Matlab中kalman函数说明

    y〔n〕=Cx〔n〕 为 A = 〔1.1269-0.49400.1129 1.0000 0 B = 〔-0.3832 0.5919 0.5191〕; C = 〔1 0 0〕; 我们的目标是设计 Kalman 滤波...

  • kalman

    卡尔曼全名 Rudolf Emil Kalman,匈牙利数学家,1930 年出生于匈牙利首都布达佩斯。...4. 简单例子 (A Simple Example) 这里我们结合第二第三节, 举一个非常简单...

  • kalman滤波matlab实现

    (cm == 'A') mtype = 2; else error('Unkown measurement model.'); ...(sd,T.nmeas); % Kalman gain % Initialize filter L_init = L_max/2.0...

  • Kalman Filter介绍

    Kalman Filter介绍_数学_自然科学_专业资料。卡尔曼滤波(kalman filter)最简单...4 简单例子(A Simple Example) 这里我们结合第二第三节,举一个非常简单的例子...

  • Kalman滤波器的基本原理及仿真

    (A,[B B],C,0,-1,'inputname',{'u' 'w'},'outputname','y'); Q = 1; R = 1; [kalmf,L,P,M] = kalman(Plant,Q,R); kalmf = kalmf(...

  • Kalman滤波及其实现(含代码4)

    Kalman 滤波 在学习卡尔曼滤波器之前,首先看看为什么叫“卡尔曼”。跟其他著名...(k-1k-1)对应的 covariance,A’表示 A 的转置矩阵,Q 是系统过程的 ...

  • Kalman滤波五大公式推导

    Kalman滤波中文版 17页 1下载券 kalman滤波的C与C++实现 10页 1下载券 ... Kalman滤波的公式推导...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email