文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces
侵权投诉

Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces

Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces

Designer Checklist

Table1. DDR3 Designer’s Checklist (continued)

Item10.11.12.13.

Description

Has the VTT island been properly decoupled with bulk decoupling? At least one bulk cap (100–220μF) capacitor should be at each end of the island.

Has the VTT island been placed at the end of the memory channel and as closely as possible to the last memory bank? Is the VTT regulator placed in close proximity to the island?Is a wide surface trace (~150 mils) used for the VTT island trace?

If a sense pin is present on the VTT regulator, is it attached in the middle of the island?

VREF

14.15.16.17.18.19.

Is VREF routed with a wide trace? (Minimum of 20–25 mil recommended.)

Is VREF isolated from noisy aggressors? In addition, maintain at least a 20–25 mil clearance from VREF to other traces. If possible, isolate VREF with adjacent ground traces.

Is VREF properly decoupled? Specifically, decouple the source and each destination pin with 0.1uf caps.Does the VREF source track variations in VDDQ, temperature, and noise as required by the JEDEC specification?Does the VREF source supply the minimal current required by the system (memories + processor)?If a resistor divider network is used to generate VREF, are both resistors the same value and 1% tolerance?

Routing

20.

The suggested routing order within the DDR3 interface is as follows:1.Data address/command2.Control3.Clocks4.Power

This order allows the clocks to be tuned easily to the other signal groups. It also assumes an open critical layer on which clocks are freely routed.

Global items are as follows:

Do not route any DDR3 signals overs splits or voids.

Traces routed near the edge of a reference plane should maintain at least 30–40 mil gap to the edge of the reference plane.

Allow no more than 1/2 of a trace width to be routed over via antipad.

When routing the data lanes, route the outermost (that is, longest lane first) because this determines the amount of trace length to add on the inner data lanes.

The max lead-in trace length for data/address/command signals, are not longer than 7 inches?Are the clock pair assignments optimized to allow break-out of all pairs on a single critical layer?

Yes/No

21.

22.23.24.

Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces,Rev. 3

Freescale Semiconductor

3

上一页第3页

你可能喜欢

热门文档

相关文档

  • DDR3 Design Considerations for PCB Applications

    DDR3 Design Considerations for PCB Applications_计算机...2007. TM 10 Key DDR3 Memory Improvements and ...Hardware and Layout De... 14页 4下载券 喜欢此...

  • 经典DDR3 PCB设计指导

    Signal Integrity and PCB layout considerations for DDR2-800 Mb/s and DDR3...or targeted design of architecture, hardware, FPGA, RF, software/firmware, ...

  • AN2910

    2, 03/2007 Hardware and Layout Design Considerations for DDR2 SDRAM Memory Interfaces by DSD Applications Freescale Semiconductor, Inc. Austin, TX The ...

  • Layout Considerations for Switchers

    Hardware and Layout De... 14页 10财富值 SAFETY CONSIDERATIO... 8页 免费...Via considerations: For microvias design for 1A/via max For 14 mil ...

  • MPC8308RDB User Guide

    MPC8308 PowerQUICC II Pro Processor Hardware Specifications (MPC8308EC) ? Hardware and Layout Design Considerations for DDR Memory Interfaces (AN2582) NOTE ...

  • ...Power ESD and Layout Design Considerations_免费...

    Hardware and Layout Desi... 14页 10财富值 Design considerations fo... 暂无...Power layout Design considerations Asia Tech Day 2009 2 Definitions ? ...

  • 基于FPGA设计的DDR接口注意事项

    for DDR SDRAM & RLDRAM II Stratix II Memory ...layout; simulate your design including PCB and ...Board Considerations ? Micron has a lot of very...

  • AN_DDR and DDR2 SDRAM ECC reference Design

    Hardware and Layout De... 16页 4下载券 喜欢此文档的还喜欢 针对DDR2-800...SDRAM ECC Reference Design Table 5 shows the memory controller interface ...

  • MTK_DDR_Rule

    We can categorize DDR SDRAM interfaces into 4 ...interface is the first priority for your design....71 High Speed Memory Layout Considerations ? ...

  • Component and Layout Considerations for DCDC Conver...

    Design and Analysis of T... 暂无评价 7页 8财富值 signal integrity and PCB... 16页 免费 SAFETY CONSIDERATIONS... 8页 免费 Hardware and Layout Desi....

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email