文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces
侵权投诉

Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces

Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces

Designer Checklist

1Designer Checklist

Table1. DDR3 Designer’s Checklist

In the following checklist, some of the items are phrased as question, others as requirements. In all cases, it is recommended to consider the line item and check it off in the rightmost column of Table1.

ItemDescriptionSimulation

Yes/No

1.

Have optimal termination values, signal topology, trace lengths been determined through simulation for each signal group in the memory implementation? If on-die termination is used at both the memories and the controller, no additional termination is required for the data group.The following unique groupings exist:

1.2.3.4.These groupings assume a full 72-bit data implementation (64-bit + 8 bits of ECC). Some products may only the optional MAPAR_OUT should be Does the selected termination scheme meet the AC signaling parameters (voltage levels, slew rate, and overshoot/undershoot) across all memory chips in the design?

2.

Termination Scheme

It is assumed that the designer is using the mainstream termination approach as found in commodity PC motherboards.

Specifically, it is assumed that on-die termination is used for the data groups and that external parallel resistors tied to VTT are used for the Address/CMD and the control groups. Consequently, differing termination techniques may also prove valid and useful. However, they are left to the designer to validate through simulation.3.4.

Is the worst case power dissipation for the termination resistors within the manufacturer’s rating for the selected devices? See Section2, “Termination Dissipation.”

If resistor packs are used, have data lanes been isolated from the other DDR3 signal groups?

Note: Because on-die termination is the preferred method for DDR3 data signals, external resistors for the data group should not be required. This item would only apply if the ODT feature is not used.

Have VTT resistors been properly placed? The RT terminators should directly tie into the VTT island at the end of the memory bus.

Is the differential terminator present on the clock lines for discrete memory populations? (DIMM modules contain this terminator.)

VTT Related Items

7.89.

Has the worst case current for the VTT plane been calculated based on the design termination scheme? See Section2, “Termination Dissipation.”

Can the VTT regulator support the steady state and transient current needs of the design?

Has the VTT island been properly decoupled with high frequency decoupling? At least one low ESL cap, or two standard decoupling caps for each four-pack resistor network (or every four discrete resistors) should be used. In addition, at least one 4.7-μF cap should be at each end of the VTT island.

Note: This recommendation is based on a top-layer VTT surface island (lower inductance). If an internal split is used, more capacitors may be needed to handle the transient current demands.

5.6.

Hardware and Layout Design Considerations for DDR3 SDRAM Memory Interfaces,Rev. 3

2

Freescale Semiconductor

上一页第2页

你可能喜欢

热门文档

相关文档

  • DDR3 Design Considerations for PCB Applications

    DDR3 Design Considerations for PCB Applications_计算机...2007. TM 10 Key DDR3 Memory Improvements and ...Hardware and Layout De... 14页 4下载券 喜欢此...

  • 经典DDR3 PCB设计指导

    Signal Integrity and PCB layout considerations for DDR2-800 Mb/s and DDR3...or targeted design of architecture, hardware, FPGA, RF, software/firmware, ...

  • AN2910

    2, 03/2007 Hardware and Layout Design Considerations for DDR2 SDRAM Memory Interfaces by DSD Applications Freescale Semiconductor, Inc. Austin, TX The ...

  • Layout Considerations for Switchers

    Hardware and Layout De... 14页 10财富值 SAFETY CONSIDERATIO... 8页 免费...Via considerations: For microvias design for 1A/via max For 14 mil ...

  • MPC8308RDB User Guide

    MPC8308 PowerQUICC II Pro Processor Hardware Specifications (MPC8308EC) ? Hardware and Layout Design Considerations for DDR Memory Interfaces (AN2582) NOTE ...

  • ...Power ESD and Layout Design Considerations_免费...

    Hardware and Layout Desi... 14页 10财富值 Design considerations fo... 暂无...Power layout Design considerations Asia Tech Day 2009 2 Definitions ? ...

  • 基于FPGA设计的DDR接口注意事项

    for DDR SDRAM & RLDRAM II Stratix II Memory ...layout; simulate your design including PCB and ...Board Considerations ? Micron has a lot of very...

  • AN_DDR and DDR2 SDRAM ECC reference Design

    Hardware and Layout De... 16页 4下载券 喜欢此文档的还喜欢 针对DDR2-800...SDRAM ECC Reference Design Table 5 shows the memory controller interface ...

  • MTK_DDR_Rule

    We can categorize DDR SDRAM interfaces into 4 ...interface is the first priority for your design....71 High Speed Memory Layout Considerations ? ...

  • Component and Layout Considerations for DCDC Conver...

    Design and Analysis of T... 暂无评价 7页 8财富值 signal integrity and PCB... 16页 免费 SAFETY CONSIDERATIONS... 8页 免费 Hardware and Layout Desi....

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email