文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > IC datasheet pdf-TPA701,pdf(700-mW Low-Voltage Audio Power Amplifier)
侵权投诉

IC datasheet pdf-TPA701,pdf(700-mW Low-Voltage Audio Power Amplifier)

IC datasheet pdf-TPA701,pdf(700-mW Low-Voltage Audio Power Amplifier)

TPA701 700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER SLOS229D– NOVEMBER1998– REVISED MAY 2003

APPLICATION INFORMATION component selection (continued) In this example, CI is 0.40µF, so one would likely ch

oose a value in the range of 0.47µF to 1µF. A further consideration for this capacitor is the leakage path from the input source through the input network (RI, CI) and the feedback resistor (RF) to the load. This leakage current creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications, as the dc level there is held at VDD/2, which is likely higher than the source dc level. It is important to confirm the capacitor polarity in the application. power supply decoupling, CS The TPA701 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1µF placed as close as possible to the device VDD lead works best. For filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10µF or greater placed near the audio power amplifier is recommended. midrail bypass capacitor, CB The midrail bypass capacitor, CB, is the most critical capacitor and serves several important functions. During start-up or recovery from shutdown mode, CB determines the rate at which the amplifier starts up. The second function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and THD+ N. The capacitor is fed from a 250-k source inside the amplifier. To keep the start-up pop as low as possible, the relationship shown in equation 10 should be maintained. This insures the input capacitor is fully charged before the bypass capacitor is fully charged and the amplifier starts up. 10 C B 250 k v 1 R )R C F I I (10)

As an example, consider a circuit where CB is 2.2µF, CI is 0.47µF, RF is 50 k , and RI is 10 k . Inserting these values into the equation 10 we get: 18.2 v 35.5 which satisfies the rule. Bypass capacitor, CB, values of 0.1µF to 2.2µF ceramic or tantalum low-ESR capacitors are recommended for the best THD and noise performance.

using low-ESR capacitors Low-ESR capacitors are recommended throughout this applications section. A real (as opposed to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the ca

pacitor in the circuit. The lower the equivalent value of this resistance, the more the real capacitor behaves like an ideal capacitor.

POST OFFICE BOX 655303

DALLAS, TEXAS 75265

IC datasheet pdf-TPA701,pdf(700-mW Low-Voltage Audio Power Amplifier)

上一页第17页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email