comparing_white_leds
energy savings by approximately 12% (Case 1). To achieve the same mean efficacy, the LED system would require an initial efficacy approximately 14% higher than the fluorescent system (Case 2).
Remember that mean lumen output for a fluorescent or metal halide lamp
is measured at 40% of rated life. For
high-performance T8 fluorescent lamps,
rated lamp life can range from 30,000 to 46,000 hours, which means that mean lumen output (and mean
luminaire efficacy) would occur after
approximately 12,000 to 18,000 hours. Major LED manufacturers generally claim design life (L70) values in excess
of 50,000 hours; the actual operating
time to reach mean luminaire efficacy will vary with the LED device and
luminaire design, and actual operating conditions. Note also that useful design life in some applications may be less than a manufacturer’s L70 value, necessitating a careful evaluation of available lumen depreciation data to estimate mean luminaire efficacy.
Light Output and Distribution
LED light output and efficacy depends on effective thermal management. However, the required heat sink surface area can limit the installed density, input power, and lumen output of LEDs—particularly in small luminaires and replacement lamps. A LED-based MR16 replacement lamp, for example, can neither aggregate enough LEDs nor provide sufficient heat sinking to match the light output and luminous intensity of a typical 50-watt tungsten-halogen MR16 today. In contrast, multiple arrays of high-flux LEDs can be assembled in larger outdoor area and roadway luminaires with integrated heat sinking, providing an energy-efficient alternative to high-pressure sodium and metal halide lamps.
Despite their comparatively low light output, LEDs are inherently directional sources and offer better optical control than traditional energy-efficient sources like fluorescent and metal halide lamps. This allows properly-designed LED luminaires to direct light where it is needed, efficiently achieving desired illumination levels and uniformity. With fewer total lumens, LED luminaires can produce high light levels on nearby surfaces (e.g., indoor applications using recessed downlights or task lighting), or low light levels on more distant surfaces (e.g., outdoor nighttime applications using pole-mounted area or roadway luminaires). As an example, Figure 1 illustrates how LED luminaires can achieve higher efficacies in directed light applications (e.g., downlights) than traditional sources. To maximize energy efficiency and lighting quality, it is important to evaluate each luminaire against the specific light level and uniformity requirements

of each application.
comparing_white_leds 4页 免费 thermal_mgt_white_leds 2页 免费 color_quality_of_white_l... 2页 20财富值 energy_efficiency_white_... 暂无评价 2页...
Color Quality of White LEDs Building Technologies Program Correlated Color Temperature (CCT) CCT describes the relative color appearance of a white light ...
29页 免费 Comparing community stru... 10页 1财富值 comparing_white_leds 4页 免费 COMPARING GENOMES 暂无评价 8页 免费喜欢此文档的还喜欢 K神贴 34页 ...
29页 免费 Comparing community stru... 10页 1财富值 comparing_white_leds 4页 免费 COMPARING GENOMES 暂无评价 8页 免费喜欢此文档的还喜欢...
Energy-Efficient Lighting Lifecycle – White Paper LED Lighting: More energy-...Figure 2: When comparing LEDs to other types of lighting systems, it is ...
11页 1财富值 comparing_white_leds 4页 免费 Normal shift shuttle bus... 4页 5财富值喜欢此文档的还喜欢 PhilipsLumileds LED 37页 免费 电能质量国际标准...
white/color LED driver from the mAhXLifeTM family...Comparing all cathodes and regulating VOUT for the...to use LEDs with consistantly lower VF voltage. ...
white/color LED driver from the mAhXLifeTM family...Comparing all cathodes and regulating VOUT for the...to use LEDs with consistantly lower VF voltage. ...
Characterizing LEDs For General Illumination Applications: Mixed-color and phosphor-based white sourcesNadarajah Narendran ,NishanthaMaliyagoda, Lei Deng, and ...
Huawei_NE5000E_White_Paper 隐藏>> Huawei NE5000E Huawei’s Multi-Chassis ...19 Comparing the CRS-1 to the NE5000E ......
热门文档