TK-3170/3173
REALIGNMENT
How to enter the password with the selector;
If the selector is rotated while “CLN LOCK” is displayed,numbers (0 to 9) are displayed flashing. When you pressthe [C] key, the currently selected number is determined.If you press the [S] key after entering the password in thisprocedure, “CLONE” is displayed if the entered passwordis correct. If the password is incorrect, “CLN LOCK” isredisplayed.
4.Power on the slave transceiver.
5.Connect the cloning cable (part No. E30-3410-05) to theSP/MIC connectors on the master and slave.
6.
Press the [S] key on the master while the master displays“CLONE”. The data of the master is sent to the slave.While the slave is receiving the data, “PROGRAM” is dis-played. When cloning of data is completed, the masterdisplays “END”, and the slave automatically operates inthe User mode. The slave can then be operated by thesame program as the master.
7.
The other slave can be continuously cloned. When the [S]key on the master is pressed while the master displays“END”, the master displays “CLONE”. Carry out the op-eration in step 4 to 6.
Notes:
Cannot be cloned if the password (over write password) isprogrammed to the slave.
Only the same models can be cloned together.

Cloning cableFig. 2
8. Self-Programming Mode

This mode allows you to write the frequency data and sig-naling, etc. to the equipment. This mode is to be used ONLYby authorized service personnel who are maintaining theuser’s equipment. After programming, reset the FPU to dis-able “Self- Programming” mode. Radios CANNOT be deliv-ered to the end-user with self-programming mode enabled.
8-1. Entering Self-Programming Mode
Remove D14 on the control unit (X57 B/4) first.
1.Press and hold the [C] key for 2 seconds while turning thepower on.
2.When self-programming mode is enabled, “ SELF ” ap-pears on the display.
Fig. 3
8-2. Adding a Data Password
If a data password is set in the optional feature menu, youmust enter the password to activate self-programmingmode.
The password can consist of 6 digits, ranging from 0~9.
■ To enter the password using the keypad:
1.Press a key while “SLF.LOCK.R” or “SLF.LOCK.W” isdisplayed. The number that was pressed will appear onthe display.
2.Each press of the key shifts the display in order to the left.3.When you have entered the entire password, press the[*
] or [S] key. “SELF” appears on the display if the en-tered password is correct. If the password is incorrect,“SLF.LOCK.R” or “SLF.LOCK.W” is redisplayed.
■ To enter the password using the selector:
1.Rotate the selector while “SLF.LOCK.R” or “SLF.LOCK.W” is displayed. A number (0 to 9) will appear on thedisplay and flash.
2.Press the [C] key. The currently selected number is set.3.When you have entered the entire password, press the [S]key. “SELF” appears on the display if the entered pass-word is correct. If the password is incorrect, “SLF.LOCK.R” or “SLF.LOCK.W” is redisplayed.
Notes:
Self-programming mode cannot be set when it has beendisabled by the FPU.
Self-programming mode for the TK-3173 transceiver can-not be enabled by the FPU when the transceiver is set upfor Trunking System Data.

[C + Power on]5
KENWOOD TK-278/378 中文编程简介 KENWOOD TK-278/378 的操作模式分四种: 1、最终用户模式:即通信模式或集群设定通讯模式; 2、经销商模式:即各类功能设定模式,...
Kenwood 健伍 TK208/308 对讲机手台调整置频 TK208、308 对讲机调整 一、频率范围: ;TK208:150MHZ;TK308:450MHZ 二、本机程序主要采用三大模式:频率设定模式;...
KENWOOD TK-278/378 中文编程简介 KENWOOD TK-278/378 的操作模式分四种: 1、最终用户模式:即通信模式或集群设定通讯模式; 2、经销商模式:即各类功能设定模式,...
KENWOOD TK-208 308 使用说明书_信息与通信_工程科技_专业资料。 ... kenwood_tk_3170 暂无评价 71页 免费 KENWOOD TM-V7A使用说明 99页 免费 ...
KENWOOD对讲机tk-278g_378g说明书_信息与通信_工程科技_专业资料。KENWOOD对讲机tk-278g_378g说明书今日推荐 157份文档 2015国家公务员考试备战攻略...
Kenwood TK80_信息与通信_工程科技_专业资料。TK-80/TRCKenwood TK-80/TRC-80 简要说明: 简要说明: 发射频率:1.8---29.9999MHZ 接收频率:0.5---29....
KENWOOD TK 对讲机 使用设置方法 设置方法_信息与通信_工程科技_专业资料。KENWOOD TK 对讲机 使用设置方法 设置方法KENWOOD TK-378/278 中文说明书 2008 年 10 ...
KENWOOD TK(建伍对讲机)_电子/电路_工程科技_专业资料。发射频率很远的对讲机KENWOOD TK-378/278 中文说明书 2010-05-28 10:43 建伍TK378对讲机是一种性价比...
Kenwood TK-208308业余频段的改制_计算机硬件及网络_IT/计算机_专业资料。... kenwood_tk_3170 暂无评价 71页 免费 KENWOOD TK 对讲机 使用... 7页 免费...
热门文档