TK-3170/3173
REALIGNMENT
5-2. Connection Procedure
1.Connect the transceiver to the personal computer withthe interface cable.
2.When the POWER switch on, user mode can be enteredimmediately. When PC sends command the radio enterPC mode, and “PROGRAM” is displayed on the LCD.When data transmitting from transceiver, the red LED islights.
When data receiving to transceiver, the green LED islights.
Note:
The data stored in the personal computer must matchmodel type, when it is written into the flash memory.
5-3. KPG-22 Description
(PC programming interface cable: Option)
The KPG-22 is required to interface the transceiver to thecomputer. It has a circuit in its D-subconnector (25-pin) casethat converts the RS-232C logic level to the TTL level.
The KPG-22 connects the SP/MIC connector of the trans-ceiver to the computers RS-232C serial port.
5-4. Programming Software KPG-101D Description
The KPG-101D is the programming software for the trans-ceiver supplied on a CD-ROM. This software runs under MS-Windows 98, ME, Windows 2000 or XP on an IBM-PC orcompatible machine.
The data can be input to or read from the transceiver andedited on the screen. The programmed or edited data can beprinted out. It is also possible to tune the transceiver.
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the transceiver. This allowsthe transceiver to be upgraded when new features are re-leased in the future. (For details on how to obtain the firm-ware, contact Customer Service.)
6-2. Connection Procedure
Connect the transceiver to the personal computer (IBMPC or compatible) with the interface cable (KPG-22). (Con-nection is the same as in the PC Mode.)
6-3. Programming
1.Start up the firmware programming software (Fpro.exe).2.Set the communications speed (normally, 115200 bps)and communications port in the configuration item.3.Set the firmware to be updated by File name item.
4.Turn the transceiver power ON with the [Side2] key helddown. Then, the orange LED on the transceiver lights and“PROG 1152” is displayed.
5.Check the connection between the transceiver and thepersonal computer, and make sure that the transceiver isin the Program mode.
6.Press write button in the window. When the transceiverstarts to receive data, the “LOADING” is displayed.
4
7.If writing ends successfully, the checksum is calculatedand a result is displayed.
8.If you want to continue programming other transceivers,repeat steps 4 to 7.
Notes:
This mode cannot be entered if the Firmware Program-ming mode is set to Disable in the Programming software. When programming the firmware, it is recommend tocopy the data from the floppy disk to your hard disk beforeupdate the radio firmware.
Directly copying from the floppy disk to the radio may notwork because the access speed is too slow.
6-4. Function
1.If you press the [Side2] key while “PROG 1152” is dis-played, the display changes to “PROG 192” to indicatethat the write speed is low speed (19200 bps). If youpress the [Side2] key again while “PROG 192” is dis-played, the display changes to “PROG 384”. If you pressthe [Side2] key again while “PROG 384” is displayed, thedisplay changes to “PROG 576”. If you press the [Side2]key again while “PROG 576” is displayed, the display re-turns to “PROG 1152”.
2.If you press the [Side1] key while “PROG 1152” is dis-played, the checksum is calculated, and a result is dis-played. If you press the [Side1] key again while thechecksum is displayed, “PROG 1152” is redisplayed.
Note:
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one radio toanother by connecting them via their SP/MIC connectors.The operation is as follows (the transmit radio is the masterand the receive radio is a slave).
The following data cannot be cloned. Tuning data
Embedded message with password Serial number
The “password” of description by explanation of 1. to 7.are “Read Authorization Password”.
1.Turn the master transceiver power ON with the [B] keyheld down. If the Data password is set to the transceiver,the transceiver displays “CLN LOCK”. If the password isnot set, the transceiver displays “CLONE”.
2.When you enter the correct password, and “CLONE” isdisplayed, the transceiver can be used as the cloning mas-ter. The following describes how to enter the password.3.How to enter the password with the keypad;
If you press a key while “CLN LOCK” is displayed, thenumber that was pressed is displayed on the transceiver.Each press of the key shifts the display in order to the left.When you enter the password and press the [*
] or [S] key,“CLONE” is displayed if the entered password is correct.If the password is incorrect, “CLN LOCK” is redisplayed.
KENWOOD TK-278/378 中文编程简介 KENWOOD TK-278/378 的操作模式分四种: 1、最终用户模式:即通信模式或集群设定通讯模式; 2、经销商模式:即各类功能设定模式,...
Kenwood 健伍 TK208/308 对讲机手台调整置频 TK208、308 对讲机调整 一、频率范围: ;TK208:150MHZ;TK308:450MHZ 二、本机程序主要采用三大模式:频率设定模式;...
KENWOOD TK-278/378 中文编程简介 KENWOOD TK-278/378 的操作模式分四种: 1、最终用户模式:即通信模式或集群设定通讯模式; 2、经销商模式:即各类功能设定模式,...
KENWOOD TK-208 308 使用说明书_信息与通信_工程科技_专业资料。 ... kenwood_tk_3170 暂无评价 71页 免费 KENWOOD TM-V7A使用说明 99页 免费 ...
KENWOOD对讲机tk-278g_378g说明书_信息与通信_工程科技_专业资料。KENWOOD对讲机tk-278g_378g说明书今日推荐 157份文档 2015国家公务员考试备战攻略...
Kenwood TK80_信息与通信_工程科技_专业资料。TK-80/TRCKenwood TK-80/TRC-80 简要说明: 简要说明: 发射频率:1.8---29.9999MHZ 接收频率:0.5---29....
KENWOOD TK 对讲机 使用设置方法 设置方法_信息与通信_工程科技_专业资料。KENWOOD TK 对讲机 使用设置方法 设置方法KENWOOD TK-378/278 中文说明书 2008 年 10 ...
KENWOOD TK(建伍对讲机)_电子/电路_工程科技_专业资料。发射频率很远的对讲机KENWOOD TK-378/278 中文说明书 2010-05-28 10:43 建伍TK378对讲机是一种性价比...
Kenwood TK-208308业余频段的改制_计算机硬件及网络_IT/计算机_专业资料。... kenwood_tk_3170 暂无评价 71页 免费 KENWOOD TK 对讲机 使用... 7页 免费...
热门文档