
Recyclability/Recoverability Guidelines
1 Scope
The purpose of this specification is to aid the GM design community in designing more recyclable/recoverable vehicles that have maximum end of life value.
This design guide is written for current technology. As technology progresses the design guide will be updated.
must comply with GMW3059, Restricted and Reportable Substances for Parts, latest version. 3.1.7 Marking of Polymeric Parts. Marking of polymeric parts is required to make it easier to identify the type of material(s).
3.1.7.1 Marking of Plastic Parts. For the marking and identification of vehicle components and materials having a weight of more than 100 g, the following standards shall apply:
--``,,,,,``,,,,`,`,``,`-`-`,,`,,`,`,,`---
2 References
Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO 1043-1 ISO 1043-2 ISO 1629
ISO 11469
ISO 22628:2002
ISO 1043-1 Plastics - Symbols-Part 1: Basic
polymers ISO 1043-2 Plastics - Symbols- Part 2: Fillers
and Reinforcing Materials
ISO 11469 Plastics - Generic Identification and Marking of Plastic Products.
3.1.7.1 Marking of Rubber Parts. For the marking and identification of vehicle components and materials having a weight of more than 200 g, the following standards shall apply:
ISO 1629 Rubber - Rubbers and Lattices –
Nomenclature.
3.2 Design for Pre-Treatment.
3.2.1 Operating Fluids. Provisions shall be made in the part, system and vehicle design for fast and efficient removal of operating fluids from: Fuel Tank
Engine Oil Pan
Gearbox/Transmission Brake System
Air Conditioning System Engine Cooling System/Radiator Power Steering System Windshield Washer Fluid Shock Absorbers
2.2 GM Standards/Specifications. GMW3059 2.3 Additional References.
GM1738
GME NOA # 13
3 General Recycling Design Guidelines
3.1 Material Selection.
3.1.1 Standardize Material Selection. If possible, use the same material type(s) used on specific components or subsystems across product lines. 3.1.2 Select Recyclable Materials. Select materials for which recycling technologies are currently practiced refer to EUCAR list of proven technologies, contact GM Materials Engineering for more information.
3.1.3 Minimize the Use of Multi-Material Parts. 3.1.4 Limit Material Types Used within Part Assemblies.
3.1.5 Reduce or Eliminate Coatings. Uncoated materials are easier and less costly to recycle than coated materials.
3.1.6 Restricted and Reportable Substances for Parts (GMW3059). All materials supplied to GM
LPG Tank
CNG Tank
Note: Draining of fluids may be made by pressure, vacuum or gravity. Fluid containers should have only one low point that is easy to locate.
3.2.2 Parts and Components. Provisions shall be made in the part, system and vehicle design for
© Copyright 2006 General Motors Corporation All Rights Reserved
April 2006
Originating Department: North American Engineering Standards
Page 1 of 13
rials Engineering Department utilizing the Part Recclability/Recoverability Report Form. Reference Appendix A of GMW3116, Recyclability, Recoverability Guidelines. ...
GMW3059 GMW3116 GMW3118 GMW3121 GMW7293 GMW7294 GMW8518 GMW14011 GMW14118...Recoverability Guidelines Verification of Requirements for Side Impact/ Roof ...
(Recoverability/Survivability)), Predictability (Stability), Accuracy (Frequency...Domain Modeling Guidelines ? How to Make a Domain Model ? ? ? ? 1. ...
guidelines and checklist 设计导则与检查清单 ? ? ? ? ? ? 分析方法 ? ...recyclability and recoverability (ISO 22628) ? Design for Disassembly – DfD...
(Recoverability/Survivability)), Predictability (Stability), Accuracy (Frequency...Domain Modeling Guidelines ? How to Make a Domain Model ? ? ? ? 1. ...
热门文档