GM7455M

Decorative Interior Plastic Laminates and Films
1 Scope
This specification gives the durability requirementsfor plastic parts decorated with wood grains, orpatterns for interior trim panels. The materialsshall be classified into four types by one of threeprocessing methods: Vacuum Formable (Type A),In Mold Foil Decorated (Type B), Vacuum Form-able Soft to the Touch (Type C) or WaterborneDecorative Film (Type D). The material shall beclassified into two grades dependent upon UVexposure. The material shall also be classified bya Grade based on application exposure level.Grade I is the basic UV exposure and is the as-sumed grade if not specified. Grade II is for HighUV exposure applications, such as the IP upperetc…..
rials Engineering Department utilizing the PartRecclability/Recoverability Report Form. Refer-ence Appendix A of GMW3116, Recyclability,Recoverability Guidelines.
4 Material Type
The material type shall be specified on the partdrawing as a suffix after the specification number,i.e. GM7455M Type A. Suffix symbol PT may beadded after the type designation to specify parttesting requirements (example: GM7455M TypeA/PT).
4.1 Type A and C, Vacuum Formable. A filmwith a pattern or solid color printed on one sidewhich is laminated to a vacuum formable thermo-plastic sheet (approximately 0.5 mm thick). Afterforming, the sheet may be bonded directly to acarrier or may be injection filled and subsequentlymechanically attached to a carrier.
4.1.1 The vacuum formable sheet must readilyform to the specified contours with sharp definitionand with no objectionable loss of pattern, glossing,blistering or wrinkling.
4.1.2 In cases where an adhesive is used to attachthe decorative sheet (either die cut or vacuumformed into shape) to a carrier, the bonding of thedecorative sheet to the carrier must meet the re-quirements of GM3602M for non flexible adher-ents.
4.2 Type B – In Mold Foil Decorated. A specialformable hot stamp foil which is applied to a clearfilm carrier on a continuous roll which is drawnthrough the injection mold. The pattern is subse-quently transferred from the carrier to the firstsurface of the plastic part during the molding proc-ess. To obtain consistent finish appearance, thepart substrate material should generally be thecolor of the pattern background.
2 References
Note: Only the latest approved standards are ap-plicable unless otherwise specified.2.1 Normative.ASTM D4060SAE J1756SAE J18852.2 GM.GM2617MGM3602MGM3807MGM4465PGM4466PGM9071PGM9150PGM9220PGM9505PGM9507PGM9517PGM9538PGM9900PGMW3059GMW3116
3.1 Color and Pattern. The color and patternshall be approved by the engineering departmentas an acceptable match to the engineering ap-proval sample when viewed under conditions setforth in GM9220P.
3.2 Recyclability, Recoverability Guidelines.Materials developed to this specification shall beoptimized to provide maximum end-of-life cyclevalue utilizing the Vehicle Recyclabiity/Recov-erability Calculation Sheet. Recycled content shallbe reported to the approving and procuring MateDecember 2001
Copyright General Motors North America Provided by IHS under license with GM
No reproduction or networking permitted without license from IHS
Note: Parts made by this process may requirethat a clear protective topcoat be applied afterbeing molded to meet wear resistance and allother performance requirements of this specifica-tion. In low wear applications, parts may not needa protective topcoat. Non topcoated parts may be
© Copyright December 2001 General Motors Corporation All Rights Reserved
Originating Department: North American Engineering Standards, Records and Documentation
Licensee=Faurecia (sites 26-29)/5967518004, User=Michael Colletti, ISPG - AubuNot for Resale, 10/12/2007 15:21:31 MDTclass
Page 1 of 4
--``,`,,,,,`,,`,,,,,`,`,,````,`-`-`,,`,,`,`,,`---
3 Requirements
52页 免费 GM7455M 4页 免费 Roland_Berger_Fight_or_f... 32页 5财富值 McKinsey Assessment Appr... 11页 免费搜你所想,读你所爱 拒绝盗版,营造绿色...
52页 免费 GM7455M 4页 免费 Roland_Berger_Fight_or_f... 32页 5财富值 McKinsey Assessment Appr... 11页 免费搜你所想,读你所爱 拒绝盗版,营造绿色...
热门文档