中文版本
load. This is achieved by introducing a safety factor, S2, such that the ratio between material ultimate stress and calculated stress shall be greater than or equal to S2 .
必须规定最大设计载荷和失效载荷之间的安全极限。这通过引入安全系数S2来实现,这样材料极限应力和计算应力之比应大于或等于S2 。

*
where:
其中:
Rm is the material ultimate stress, in N/mm2
Rm是材料极限应力,单位 N/mm2
σc is the calculated stress, in N/mm2.
σc 是计算应力,单位N/mm2。
Usually S2=1.5, but the factor may be reduced when at least one of the following conditions is fulfilled:
通常S2=1.5,当下列条件中至少有一条得到满足,此系数可以减少:
a) there are alternative load paths;
a) 有可供选择的载荷路径;
b) for parts of the structure which are specifically designed to collapse in a controlled manner; b) 对于在可控状态下特殊设计结构的零部件;
c) the calculations are sufficiently detailed to give high confidence in the performance of the critical areas of the structure.
c) 计算充分详细地对结构评定区域的性能给出高可信度。
The treatment of stress concentration as indicated in 3.4.2 also applies in this case. However, the effect of stress concentration shall be considered in more detail for brittle materials where local plastic yielding, as a mechanism for stress redistribution at the concentration, does not occur.
3.4.2中说明的对应力集中的处理也适用于本工况,然而当不出现作为一个在集中处应力重新分布机制的局部塑性屈服时,对脆性材料应更详细地考虑应力集中的影响。
A reduction in the value of S2 shall be agreed between the operator and designer.
S2数值的减少应在运营者和设计者之间协商决定。
3.4.4 Stability 稳定性
Local instability, in the form of elastic buckling, is permissible provided alternative load paths exist and the yield or proof criteria are met.
假如可选择载荷路径存在和满足标准的屈服或弹性极限,以弹性挤曲形式的局部屈服是允许的。
The vehicle structure shall have a margin of safety against instability leading to general structural failure. This is to be achieved by ensuring that the ratio of the critical buckling stress to the calculated stresses shall be greater than or equal to S3:
车辆结构应有一个抵抗导致总体结构失效的不稳定性的安全限度。这是通过确保临界屈曲应力与计算应力的比值大于或等于S3来实现的:

S2 incorporates the uncertainty factor S1.
S 包含有不确定系数S。
BS EN 12663:2000 铁道应用— 轨道车身的结构要求欧洲标准 EN 12663:2000 具有... EN 12663:2003铁路应用... 28页 1下载券 JIS E7105-1989 中文版 ... ...
EN 12663:2003铁路应用... 28页 1下载券 基于柔性车体的铁道车辆... 5页...缩拘 谶计 文章 编号:0271(O8O一0 9O 10-6020)1OO一3 9 铁道车辆车体结构...
铁道车辆车体结构技术_专业资料。以车底部、侧墙板、车顶板结构为重点,阐述了车辆的车体(薄壳)结构技术,并介绍了车体刚度与车体各部分的关系。...
BS EN 12663-2000_工作总结/汇报_总结/汇报_应用文书。车体强度标准BS EN 12663∶2000 英国标准 BS EN 12663∶2000 铁路应用—铁路车辆车体的结构强度要求 本...
EN 12663 铁路应用——铁道车辆车体结构要求 3 术语和定义 为了本文件的目的,在本文中使用下列术语和定义: 3.1 主动安全 为了防止碰撞发生的目的而采用的系统和...
过高的刚度评定值制约了车体轻量 化设计。 UIC 577 1998 货车应 力! 和 EN 12663 2009 铁路应用 铁道车辆车体结构要求!均指出车体结构 应保证适宜的刚度, 使...
铝结构通过螺栓进行连接; 车体结构设计满足 EN 12663《铁路车辆车体结构要求》...第三种,在车体结构中应用整体结构,板皮和纵向加固件构成高强度大型开 口型材。...
EN 12663:2003铁路应用 铁... 28页 2财富值 EN 12663 28页 免费 BS EN... 轨道车身的结构要求轨道车身的结构要求隐藏>> 3.2 轨道车辆的类别 3.2.2 ...
EN 12663:2003铁路应用... 28页 1下载券北京地铁房山...“铁道车辆车体结构 要求”和T B/T1335-1996《铁道车 辆强度设计及试验鉴定...
EN12663—2000《铁路应用—铁道车辆车体结构的强度要求》 14. UIC515-3/1994《...UIC515-1/2003《客车—拖车转向架—走行部—抬车转向架结构部 件的一般规定...
热门文档