文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > 无损检测工艺规程(超 声 波 检 验)
侵权投诉

无损检测工艺规程(超 声 波 检 验)

无损检测工艺规程(超 声 波 检 验)-双语版

NJBST Co.,Ltd.

QCD-013

Rev.:0

Page:4 of 12

Title: ULTRASONIC EXAMINATION PROCEDURE 4.2 探头 4.2 Search Unit For straight beam, the diameter of transducer shall be 直探头直径应为 14~25mm.斜探头应根 14mm-25mm. For angle beam, an angle shall be selected as 据被检工件厚度适当选用(参照下表): appropriate for the configuration being examined. The following search units are recommended to be used in examination: Search Unit type 2.5P 8x12 2.5P 8x12 2.5P 8x12 2.5P 8x12 Beam Angle(β) 450 560 63 0

Frequency 2.5MHz 2.5MHz 2.5MHz 2.5MHz

Manufactured by Shantou, China Shantou, China Shantou, China 2.5P 8x12 探头 2.5P 8x12

折射 角 (β) 450 560 630 680

频率 2.5MHz 2.5MHz 2.5MHz 2.5MHz

制造 单位 汕头超声 仪器厂 汕头超声 仪器厂 汕头超声 仪器厂 汕头超声 仪器厂

680

Shantou, China 2.5P 8x12 2.5P 8x12

The range of angle is recommended as following: Wall Thickness (mm) 8-25 >25-46 >46 Beam Angle (β) 720-630 68 -56 0 0

探头折射角与被检壁厚关系:

K Value (tgβ) 3.0-2.0 2.5-1.5 2.0-1.0 壁厚(mm) 8-25 >25-46 >46 折射角(β) 720-630 68 -56 0 0

K 值 (tgβ) 3.0-2.0 2.5-1.5 2.0-1.0

630-450

630-450

4.3 Frequency Generally, the frequency of 2.5MHz shall be used. For the thinner plate, 5MHz may be used. 4.4 Screen Height linearity The ultrasonic instrument shall provide linear vertical presentation within±5% of the full screen height for 20% to 80 of the calibrated screen height (base line to maximum calibrated screen point(s)). The procedure for evaluating screen height linearity is provided in Appendix Ⅰof ASME Code Sect. V Sub. A Artic

le 5 and shall be performed at the beginning of each period of extended use (or every 3 months, whichever is less). 4.5 Amplitude Control Linearity The ultrasonic instrument shall utilize an amplitude control accurate over its useful range to ±20% of the nominal amplitude ratio, to allow measurement of indications beyond the linear range of the vertical display on the screen. The procedure for evaluating amplitude control linearity is given in ASME Sect V. Art .5. Appendix Ⅱand shall be performed at the beginning of each period of extended use(or every 3 months, whichever is less). 4.6 Checking and Calibration of Equipment The proper functioning of the examination equipment shall be checked and the equipment shall be calibrated by the use of the calibration standard at the beginning and end of each examination., when examination personnel are changed, and at any time that malfunctioning is suspected as a minimum. If during any check it is determined that the testing equipment is not functioning properly, all of the product that has been tested since the last valid equipment calibration shall be reexamined. 5. CALIBRATION 5.1 Basic Calibration Block Configuration

4.3 频率 通常应频率 2.5MHz,对薄板,可采用 5MHz . 4.4 屏高线性 超声应提供±5%满屏高的垂直线性 (在 20%至 80%校正屏高的范围内). 屏高线性的测评方法按 ASME 第 V 卷 A 篇第 5 章附录Ⅰ,应在每一周期开始 (或每 3 个月,取两者中时短者)测评一 次. 4.5 波幅控制线性 为能测量示波屏上超出垂直线性范围 的信号,超声仪应有在有用范围内可精 确到标称波幅比±20%的波幅控制器. 评定波幅控制线性的方法,见 ASME 第 V 卷第 5 章附录Ⅱ.此评定应在每一延 长使用周期开始时进行(或每 3 个月进行 一次,取两者中较短的时间). 4.6 设备校验 对探伤设备应使用校正试块于每次检查 开始和结束时进行性能校验,当探伤人 员更换时, 或怀疑有故障时, 也要校验. 校验时发现探伤设备性能不佳时,所有 产品均应重新检查(自设备上次有效校 验算起). 5. 校正 5.1 基本校正试块

无损检测工艺规程(超 声 波 检 验)

上一页第4页

你可能喜欢

  • 无损检测通用工艺
  • 超声波探伤标准
  • 超声波探伤操作规程
  • X射线无损探伤
  • ASME标准讲解
  • 焊接验收标准
  • 射线检测工艺卡
  • 渗透检测

热门文档

相关文档

  • 超声波检测工艺规程

    超声波检测工艺规程_机械/仪表_工程科技_专业资料...承压设备无损检测 GB50235-1997 工业金属管道工程... 在达到所检工件最大声程时,其灵敏度余量应≥10...

  • 无损检测工艺规程1

    无损检测工艺规程1_机械/仪表_工程科技_专业资料...无 损 检 测 工 艺 规 程 ZW09-04-08 总份...标准 11 条标准 11.3 附录C 超 声 波 探 伤 ...

  • 无损探伤工艺及超声波应用

    无损探伤工艺及超声波应用_信息与通信_工程科技_...无损检测工艺规程无损检测工艺规程是按本单位的受检...焊缝的超声波检测———可用直射声束法或斜射声束法...

  • 无损探伤检测工艺规程

    单斜探头、双晶探头等,在达到所检 工件的最大检测声程时,其有效灵敏度余量≥... 超声波探伤工艺规程 9页 免费 无损检测工艺规程(液体渗... 9页 免费 无损...

  • 超声波探伤操作工艺规程

    超声波探伤操 作工艺规程 1. 主题内容与适用范围 ...2 引用标准 JB4730-2005《 承压设备无损检测》 JB...a 仪器和探头的组合灵敏度:在达到所检工件最大声...

  • 无损检测工艺规程

    本规程规定了无损检测人员应具备的资格,本公司所采用的四种无损检测方法射线检 测、超声检测、磁粉检测和渗透检测,检测设备,检测工艺,检测时机,验收标准及档案的 ...

  • 02无损检测工艺规范

    探伤工艺规范 超声波探伤工艺规范 磁粉探伤工艺规范 ...d. 探头主声束应无双峰、无偏斜。 2.2.2 采用...是被检焊缝的厚度,两厚度不等的焊接件,T 则是两...

  • 超声波检测工艺规程

    超声波检测工艺规程_机械/仪表_工程科技_专业资料...3 引用标准 JB4730《压力容器无损检测》 GB150《... 在达到所检工件最大声程时,其灵敏度余量应≥10...

  • 无损检测工艺规程

    无损检测工艺规程_六年级其它课程_其它课程_小学...1.6 校准 校准在基准试块上进行,使超声波主声束...2.8.8 复验 当决定复验时,必须对被检面进行...

  • 超声无损检测通用工艺

    超声无损检测通用...超声波检测通用工艺规程编制: 编制: 审核: 审核: ...按表2选择和使用 DAC 曲线灵敏度,按表3进行验 收...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email