无损检测工艺规程(超 声 波 检 验)-双语版
NJBST Co.,Ltd.
QCD-013
Rev.:0
Page:3 of 12
Title: ULTRASONIC EXAMINATION PROCEDURE 1.适用范围 1. SCOPE OF APPLICATION This procedure is compiled in accordance with the requirements of 1.1 本规程按 ASME 第 V 卷和第 Ⅷ第 1 分册要求编制. ASME Code Section V and Section Ⅷ Division 1. 1.2 In accordance with this procedure a pulse-echo type of ultrasonic 1.2 按规程对规范产品的检查用脉 instrument shall be used for Code product examination. Single probe, 冲反射式超声波探伤仪.以单斜 angle beam scanning shall be the principal method, if necessary, straight 探 头扫查为主要方法,必要时可 辅以直探头扫查. beam scanning may also be used. 1.3 This procedure is applicable for ultrasonic examination of 1.3 本规程适用于板厚≥8mm 钢 butt-welded, full penetrated joint in wrought ( rolled, drawn, forged or 制压力 容器全焊透对接焊缝的 extruded) material with thickness equal to or greater than 5/16in.(8mm) 超声检查(包括焊缝金属和热影响 detecting, locating and evaluating the reflectors from the weld metal, 区). 1.4 本规程不适用于单面焊部分焊 heat affected zone and base metal adjacent the weld. 1.4 Ultrasonic examination of single side welded partial penetrated welds 透焊缝的检查,也不适用于奥氏 and austenitic steel welds are not considered to be within the scope of 体钢焊缝的的检查. 1.5 除非其他程序经批准,有关具 this procedure. 1.5 Unless other procedure has been approved and accepted that may 体要求经认可,UT 有关方法,评 specify particular requirements, ultrasonic examination relating to 定,要求应按本规程. method, evaluation, and detailed technique and requirement shall be in 2.无损探伤人员 2.1 无损探伤人员应按本公司根据 accordance with this procedure. SNT-TC-IA(现行版)制定的"NDE 2. NDE PERSONNEL 2.1 NDE personnel shall be qualified and certified according to 人员培训,考试,资格鉴定和认 NJBST'S Written Practice QCD-011 based on SNT –TC-IA (Current 证的实施细则"进行资格鉴定和 认证. Code Accepted Edition). 3.一般探伤要求 3. GENERAL EXAMINATION REQUIREMENTS 3.1 探测范围 3.1 Examination coverage
应通过探头在探测面的移动, The volume shall be examined by moving the search unit over the 使焊缝全体积均受超声束扫查. examination surface so as to scan the entire examination volume .Each pass of the search unit shall overlap a minimum of 10% of the transducer 探头的扫查路径应至少重叠探头 (piezo-electric element) dimension perpendicular to the direction of the 横向宽度的 10% 3.2 探头移动速度 scan. 探伤时,探头移动速度应不大 3.2 Speed of Search Unit Movements 于 150mm/s. The speed of search unit movement for examination shall not exceed 6 3.3 记录水平 in./sec (150mm/sec.) 凡波高超过 50% DAC 基准线而 3.3 Recording Level 未予返修的讯号均应记录在案. All reflections from uncorrected areas having responses that exceed 50% 4.超声仪,探头和参数 of reference level shall be recorded. This record shall locate each area, 4.1 超声仪 the response level, the dimensions, the depth below the surface, and the 应使用下列脉冲反射式超声仪: classification. 4. ULTRASONIC INSTRUMENT, SEARCH UNIT AND PARAMETERS 4.1 Ultrasonic Instrument A pulse-echo type of ultrasonic instrument shall be used. The following instruments are recommended in examination. Instrument Type CTS-26 Manufactured by Shantou, China 仪器型号 CTS 26 制造单位 汕头超声仪器厂

超声波检测工艺规程_机械/仪表_工程科技_专业资料...承压设备无损检测 GB50235-1997 工业金属管道工程... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程1_机械/仪表_工程科技_专业资料...无 损 检 测 工 艺 规 程 ZW09-04-08 总份...标准 11 条标准 11.3 附录C 超 声 波 探 伤 ...
无损探伤工艺及超声波应用_信息与通信_工程科技_...无损检测工艺规程无损检测工艺规程是按本单位的受检...焊缝的超声波检测———可用直射声束法或斜射声束法...
单斜探头、双晶探头等,在达到所检 工件的最大检测声程时,其有效灵敏度余量≥... 超声波探伤工艺规程 9页 免费 无损检测工艺规程(液体渗... 9页 免费 无损...
超声波探伤操 作工艺规程 1. 主题内容与适用范围 ...2 引用标准 JB4730-2005《 承压设备无损检测》 JB...a 仪器和探头的组合灵敏度:在达到所检工件最大声...
本规程规定了无损检测人员应具备的资格,本公司所采用的四种无损检测方法射线检 测、超声检测、磁粉检测和渗透检测,检测设备,检测工艺,检测时机,验收标准及档案的 ...
探伤工艺规范 超声波探伤工艺规范 磁粉探伤工艺规范 ...d. 探头主声束应无双峰、无偏斜。 2.2.2 采用...是被检焊缝的厚度,两厚度不等的焊接件,T 则是两...
超声波检测工艺规程_机械/仪表_工程科技_专业资料...3 引用标准 JB4730《压力容器无损检测》 GB150《... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程_六年级其它课程_其它课程_小学...1.6 校准 校准在基准试块上进行,使超声波主声束...2.8.8 复验 当决定复验时,必须对被检面进行...
超声无损检测通用...超声波检测通用工艺规程编制: 编制: 审核: 审核: ...按表2选择和使用 DAC 曲线灵敏度,按表3进行验 收...
热门文档