高速I/O接口设计
If you overlook any of the Altera PCB recommendations, assess the impact on the
PDN and the operation of the transceiver and correct where possible.
Add Decoupling
Local decoupling capacitors are essential to the integrity of the power supply when
measured at the load. The amount and value of any decoupling scheme is highly
dependent upon the PCB design and also the FPGA design.
You can use the Altera Power Distribution Network Tool to help design your
transceiver power supplies according to their specific design. The tool may also be
used as a debugging aid to assess the effectiveness of a PDN.
fFor more information, refer to the The Altera Power Distribution Network Tool User
Guide.
If after assessing all of the design PDN and decoupling schemes, you find that there is
insufficient decoupling, add some more by one of the following methods:
■
■Replace larger bulk capacitors with higher values.If you require more decoupling on a board that is already designed and
manufactured, solder small 0402 or 0201 capacitors onto the back of the ball-grid
array (BGA) breakout vias.
For a less effective method of adding extra decoupling, piggy-back extra
capacitors on top of existing capacitors. This method is less effective, because
power and ground vias are effectively shared.■
Although the above methods are not ideal for high volume production, you must
clean the supplies sufficiently to meet requirements and hence debug the design.
Replace or Short-Circuit Series Filter or Inductor
Altera recommends you do not use switch-mode regulators and series inductors to
provide a clean and cheap supply, instead of using linear regulators.
Switch-mode regulators typically have an order of magnitude more noise than a
linear regulator. In addition, if the series inductor is incorrectly chosen, and
insufficient downstream decoupling capacitance is applied, the inductor can starve
the FPGA supply pins of instantaneous current, cause the voltage to drop, and
increase supply noise that the FPGA sees.
A simple and effective experiment is to replace the series inductor with a zero-ohm
resistor or direct short circuit. You should ensure that the power capability of any
resistor is sufficient. Implementing a short circuit ensures that any instantaneous
current required by the transceiver can be sourced by the regulator quicker than if you
use an inductor.
1Replacing the series inductor with a 0-Ω resistor may also increase noise as the
filtering effect of the inductor is removed.
第17卷V01.17 第3期No.3 电子设计工程ElectronicDesignEngineering 2009年3月Mat.2009 高速USB接口设计甄国涌.张森峰(中北大学电子潮试技术国家重点实验室,山西...
第17 卷 第3期 Vol.17 No.3 电子设计工程 Electronic Design Engineering 2009 年 3 月 Mar.2009 高速 USB 接口设计甄国涌 , 张森峰(中北大学 电子测试技术...
DDR+SDRAM与FPGA的高速接口设计_信息与通信_工程科技_专业资料。介绍关于FPGA DDR 控制器的专业文档可轴糕器件盛.属 DDR 电子测豢技术 ELECTR()NIC 第3l卷第n...
基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业...
ADI公司TigerSHARC系列DSP芯片TS201性能优越,在高速实时信号处理中得到广泛应用,而其中对TS201的通信接口设计成为保证其高速实时性能的关键。对TS201与FPGA之间两种主要...
STM32F103的高速以太网接口设计_计算机硬件及网络_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 STM32F103的高速以太网接口设计_计算机硬件及网络_IT/...
基于STM32F107的高速以太网接口设计与应用_工学_高等教育_教育专区。基于STM32F107的高速以太网接口设计与应用Network and Multimedi 文章编号: 1002-8684 (2011) 09...
Gbps试验系统中高速串行接口的设计与实现_专业资料。介绍Gbps无线通信试验系统中高速串行数据接口的设计与实现。按照Gbps无线通信试验系统对高速串行数据的传输要求,数据...
基于FPGA的高速通信接口设计_信息与通信_工程科技_专业资料。基于FPGA的高速通信接口设计2005年9月 第3期 实验科学与技术 基于FPGA的高速通信接口设计。 A砸ghSpeed...
基于TMS320C6455的高速SRIO接口设计_信息与通信_工程科技_专业资料。RapidIO互连架构是一个开放的标准,满足了嵌入式基础设施在应用方面的广泛需要。它将是未来十几年嵌...
热门文档