文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 互联网 > 高速接口设计
侵权投诉

高速接口设计

高速I/O接口设计

What to Do with Noisy Power Supplies

If the transceiver and PLL supplies are noisy or out of specification, you should clean

them up by any available method to determine whether the noise observed is

affecting the integrity of the transceiver interface.

Filtering transceiver supplies with inductors can provide useful access points and

powerful debugging aids. They can be removed, thus isolating a potentially noisy

voltage source from the transceiver load. They also allow the introduction of

alternative cleaner power sources.

PCB Stackup

An important part of any power supply design is the PCB stackup and routing.

Ideally, you should review and check PCB stackup and routing, before PCB sign-off.

There is little that you can do to rectify any PCB oversights or mistakes after a PCB has

been manufactured, but you should still include it in any debug activities and it is a

good idea to review a PCB if power supplies are found to be noisy.

Altera gives the following recommendations

■

■Supply power to the FPGA through solid or split-plane structures.Place power and ground planes on adjacent planes that have very thin dielectric to

provide inter-plane capacitance and thus aid high frequency transient current

supply to the FPGA.

Place power and ground plane pairs close to the surface of the PCB stackup on the

same side as the FPGA.

Connect decoupling capacitors directly to the power and ground planes that they

are coupling using their own individual vias.■■

Under no circumstances should adjacent capacitors or FPGA pins share power or

ground vias. Figure5 shows two examples of bad power or ground via sharing

practices. This practice introduces mutual inductance and increases simultaneous

switching noise (SSN).

Figure5.

高速接口设计

Examples of Bad Power and GND Via Sharing

fFor further power distribution network (PDN) recommendations, refer to the High-

Speed Board Design Advisor Technical Brief.

上一页第5页

你可能喜欢

  • 软件接口设计
  • 接口设计说明
  • 接口设计文档
  • 接口设计方案
  • 接口设计规范
  • 接口技术课程设计

热门文档

相关文档

  • 高速USB接口设计

    第17卷V01.17 第3期No.3 电子设计工程ElectronicDesignEngineering 2009年3月Mat.2009 高速USB接口设计甄国涌.张森峰(中北大学电子潮试技术国家重点实验室,山西...

  • 高速USB接口设计

    第17 卷 第3期 Vol.17 No.3 电子设计工程 Electronic Design Engineering 2009 年 3 月 Mar.2009 高速 USB 接口设计甄国涌 , 张森峰(中北大学 电子测试技术...

  • DDR+SDRAM与FPGA的高速接口设计

    DDR+SDRAM与FPGA的高速接口设计_信息与通信_工程科技_专业资料。介绍关于FPGA DDR 控制器的专业文档可轴糕器件盛.属 DDR 电子测豢技术 ELECTR()NIC 第3l卷第n...

  • 基于Xilinx Spartan6的高速接口设计

    基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 基于Xilinx Spartan6的高速接口设计_电子/电路_工程科技_专业...

  • TS201高速通信接口设计及实现

    ADI公司TigerSHARC系列DSP芯片TS201性能优越,在高速实时信号处理中得到广泛应用,而其中对TS201的通信接口设计成为保证其高速实时性能的关键。对TS201与FPGA之间两种主要...

  • STM32F103的高速以太网接口设计

    STM32F103的高速以太网接口设计_计算机硬件及网络_IT/计算机_专业资料 暂无评价0人阅读0次下载举报文档 STM32F103的高速以太网接口设计_计算机硬件及网络_IT/...

  • 基于STM32F107的高速以太网接口设计与应用

    基于STM32F107的高速以太网接口设计与应用_工学_高等教育_教育专区。基于STM32F107的高速以太网接口设计与应用Network and Multimedi 文章编号: 1002-8684 (2011) 09...

  • 【论文】Gbps试验系统中高速串行接口的设计与实现

    Gbps试验系统中高速串行接口的设计与实现_专业资料。介绍Gbps无线通信试验系统中高速串行数据接口的设计与实现。按照Gbps无线通信试验系统对高速串行数据的传输要求,数据...

  • 基于FPGA的高速通信接口设计

    基于FPGA的高速通信接口设计_信息与通信_工程科技_专业资料。基于FPGA的高速通信接口设计2005年9月 第3期 实验科学与技术 基于FPGA的高速通信接口设计。 A砸ghSpeed...

  • 基于TMS320C6455的高速SRIO接口设计

    基于TMS320C6455的高速SRIO接口设计_信息与通信_工程科技_专业资料。RapidIO互连架构是一个开放的标准,满足了嵌入式基础设施在应用方面的广泛需要。它将是未来十几年嵌...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email