Application of the FactSage to Predict the Ash Melting Behavior in Reducing Conditions
785
amounts and ash transformation at high temperature under reducing conditions. The theoretical predictions were also testified by experimental investigations of ash fusion temperature (AFT) test and X-ray diffraction (XRD) for the quenched ash samples.
2 RESEARCH METHOD FactSage Thermodynamic Model was used for predicting multi-phase equilibria, proportions of the liquid and solid phases in specified atmosphere for the multi-component system. Calculation conditions for FactSage Thermodynamic Model: (1) Chemical composition The ash composition of A1203, CaO, Fe2O3, Na20, K20, MgO, Si02, SO3, P205, Ti02 was input in the table of the software. (2) Solution species FACT-SLAG solution included MgO, FeO, Na20, Si02, Ti02, Ti2O3, CaO, Al2O3, K20, MgS, CaS, FeS, Na*S, Na3P04, Ca3(P04)2,Mg3(P04)2, Fe3(P04)2. (3) Gas atmosphere The reducing atmosphere of 60% CO and 40% COz was employed in the FactSage calculation. (4) Pressure The pressure for the FactSage calculation was 0.1MPa. ( 5 ) Temperature The initial temperature and final temperature for the FactSage calculation were 800°C and 1600"C, respectivel
y with the interval of 20°C. 3 EXPERIMENTAL STUDY AND ANALYSIS 3.1 Coal samples Six typical coal samples, selected from Huainan coal basin, Anhui Province of China, were ground to less than 0.063mm (250 meshes). Coal samples are ashed in air at 815°C according to the Japan Industrial Standard (JIS). All ash samples were analyzed using Rigaku RINT X-Ray Fluorescence (XRF). The chemical compositions of the ash samples analyzed by Rigaku X-ray fluorescence and the melting temperatures of coal ash samples are presented in Table 1.
As shown in Table 1, the ash composition of Huainan coal samples is rich in Si02 and A1203 (>75%). The contents of Ti02 is higher than 1% on average, the Na20 and MgO lower than 0.5% and 1%, respectively. The contents of CaO and FeO vary greatly from about 1% to 10% with coal samples. The ground and dried coal was mounted in wax and allowed to harden. The mount was cross-sectioned and polished, coated with carbon layer to eliminate the electrostatic effects, and placed in the computer-controlled scanning electron microscope (CCSEM) for analysis. Six typical coal samples were analyzed by JEM-5600 with CDU-LEAP SEM-EDX and CCSEM. For CCSEM analyses, three magnifications, namely 150 for the 22.0-2 11.Oym, 250 for the 4.6-22.0ym and 800 for the 0.5-4.6pm were used to obtain the backscattered image of samples. The CCSEM was used to measure the size, composition, and abundance of mineral grains in the coal.
3.2 Ash fusion temperature test The melting test was carried out under a reducing condition of 60% CO and 40% C02. The ash samples were shaped into triangular cones. The cones were inserted into a furnace and heated at 5"Cmin-' ramp rate. The limit temperature of the furnace is 1500°C. In order to compare the predicted AFT with the tested AFT, the AFT of HN11.5 and HN106 coal ash with different flux addition contents was tested and calculated by FactSage respectively. 3.3 Experiment on ash by XRD A laboratory vertical gas-tight tube furnace apparatus was set up to heat the samples to high temperature under controlled atmosphere. About 1g of ash samples was heated in the apparatus which was modified to allow rapid heating and quenching of ash samples. The sample was dropped in the furnace and reacted for 5min at desired temperature range from 1050°C to 1450"C,and then was quenched into water. Total quenching time was normally 5s. Quenched samples were examined by using Rigaku RINT X-ray powder diffractometry.
Table 1 Chemical composition and melting temperature for the coal ash samples" Coal HN106 HNC13 HN115 HN119 KL1 HNPOl
Composition,% (by mass) SiOz 39.8 42.1 42.3 42.0 47.1 50.1 A1203
T,"C SO3 0.71 1.78 3.20 3.82 2.22 1.00 P205
.~ . .
Fe203 9.19 3.94 6.17 3.21 4.72 8.42
CaO 1.13 5.77 8.55 9.93 5.67 1.37
MgO 0.36 0.59 1.00 0.44 0.75 0.62
Na20 0.24 0.41 0.21 0.37 0.26 0.45
K20 2.29 1.13 0.76 0.17 1.33 2.17
Ti02 3.35 2.26 2.24 2.08 1.96 1.51
DT >1500>1500 1335 1434 1450 1425
ST>1500>1500 1360 1451 1500
1495
FT >1500 >1500 1400 1480 >1500>I500
41.8 40.2 34.5 36.9 35.3 32.9
0.20 1.22 0.55 0.2 0.19 0.34
0 Expressed as mass fraction (%) equivalent oxide, dry basis. Chinese J. Ch. E. 14(6) 784 (2006)

Chem. Eng., 14(6) 784—789 (2006) Application of the FactSage to Predict the Ash Melting Behavior in Reducing Conditions* LI Hanxu(李寒旭)a,**, ...
ago.The FactSage package preparedbycriticalevaluationand optimization ofa11 ...Application oftheFactSagetoPredicttheAshMeltingBehaviorinReducingConditionsAsshown...
melting point and viscosity of slag in steelmaking...the distribution behavior of P2O5 between solid solution...(2) The calculated results by FactSage indicat...
The computer software package FactSage was used to...These models predict the AFTs of coal ash ...ers), the content of the strongly reducing gas ...
热门文档