美制NPT螺纹标准
1860
AMERICAN PIPE THREADS
PIPE AND HOSE THREADS
The types of threads used on pipe and pipe fittings may be classed according to theirintended use: 1) threads that when assembled with a sealer will produce a pressure-tightjoint; 2) threads that when assembled without a sealer will produce a pressure-tight joint;3) threads that provide free- and loose-fitting mechanical joints without pressure tight-ness; and 4) threads that produce rigid mechanical joints without pressure tightness.
American National Standard Pipe Threads
American National Standard pipe threads described in the following paragraphs providetaper and straight pipe threads for use in various combinations and with certain modifica-tions to meet these specific needs.
Thread Designation and Notation.—American National Standard Pipe Threads are des-ignated by specifying in sequence the nominal size, number of threads per inch, and thesymbols for the thread series and form, as: 3 8—18 NPT. The symbol designations are asfollows: NPT—American National Standard Taper Pipe Thread; NPTR—AmericanNational Standard Taper Pipe Thread for Railing Joints; NPSC—American National Stan-dard Straight Pipe Thread for Couplings; NPSM—American National Standard StraightPipe Thread for Free-fitting Mechanical Joints; NPSL—American National StandardStraight Pipe Thread for Loose-fitting Mechanical Joints with Locknuts; and NPSH—American National Standard Straight Pipe Thread for Hose Couplings.
American National Standard Taper Pipe Threads.—The basic dimensions of theANSI Standard taper pipe thread are given in Table 1a.
Form of Thread: The angle between the sides of the thread is 60 degrees when measuredin an axial plane, and the line bisecting this angle is perpendicular to the axis. The depth ofthe truncated thread is based on factors entering into the manufacture of cutting tools andthe making of tight joints and is given by the formulas in Table 1a or the data in Table 2obtained from these formulas. Although the standard shows flat surfaces at the crest androot of the thread, some rounding may occur in commercial practice, and it is intended thatthe pipe threads of product shall be acceptable when crest and root of the tools or chaserslie within the limits shown in Table 2.
Pitch Diameter Formulas: In the following formulas, which apply to the ANSI Standardtaper pipe thread, E0 = pitch diameter at end of pipe; E1 = pitch diameter at the large end ofthe internal thread and at the gaging notch; D = outside diameter of pipe; L1 = length ofhand-tight or normal engagement between external and internal threads; L2 = basic lengthof effective external taper thread; and p = pitch = 1 ÷ number of threads per inch.
E0=D–(0.05D+1.1)pE1=E0+0.0625L1
Thread Length: The formula for L2 determines the length of the effective thread andincludes approximately two usable threads that are slightly imperfect at the crest. The nor-mal length of engagement, L1, between external and internal taper threads, when assem-bled by hand, is controlled by the use of the gages.
L2=(0.80D+6.8)p
Taper:The taper of the thread is 1 in 16, or 0.75 inch per foot, measured on the diameterand along the axis. The corresponding half-angle of taper or angle with the center line is 1degree, 47 minutes.
NPT螺纹标准_机械/仪表_工程科技_专业资料。NPT螺纹,可密封螺纹... 公制螺纹是 60 度等边牙型,英制螺纹是等腰 55 度牙型,美制螺纹为等腰 60 ...
是 National (American) Pipe Thread 的缩写,属于美国标准的 6 0 度锥管螺纹...879 yihe NPT 螺纹分:一般密封圆柱管螺纹和一般密封圆锥管螺纹 一、美制一般...
NPT标准螺纹数据_机械/仪表_工程科技_专业资料。介绍NPT英制螺纹标准与技术数据...标记:美制一般密封管螺纹的完整标记由螺纹特征代号,螺纹尺寸代号和旋向代号组成。...
英、美制螺纹标准直径、螺距参照表_机械/仪表_工程科技_专业资料。英、美制...(PF) 6 ‐11 美制标准管用螺纹(NPT、NPS) 51 57 63 72 78.5 85 97 ...
统一螺纹标准(美制螺纹标准)加工参考 统一螺纹标准(美制螺纹标准) 统一螺纹标准(...(美制 NPT) (牙角 60 度) 梯形螺纹 (30 度 公制) 梯形螺纹 (29 度 爱...
美制一般密封圆锥管螺纹的特征代号:NPT 美制一般密封圆柱内螺纹的特征代号:NPSC 例:尺寸代号为 4,左旋一般美制一般圆锥管螺纹: 中国标准:NPT 4-LH 美国标准:4-...
美制螺纹标准及代号_能源/化工_工程科技_专业资料。美制螺纹标准及代号...NPT NPTR NPTF PTF-SAE SHORT ANSI B2.2 60° ANSI B2.1 BS 21:1973 ...
N.P.T 为美国螺纹标准 NPT 是美标锥管螺纹 National Pipe Thread 的英文缩写...NPT 的外螺纹,也就是 National Pipe Thread Male 严格的说,NPTF 指的是美制...
NPT螺纹接头标准_机械/仪表_工程科技_专业资料。NPT,PT,G 各种螺纹的区别 ...区别,公制螺纹是 60 度等边牙型,英制螺纹是等腰 55 度牙型, 美制螺纹 60 ...
螺纹规格-美制、英制、公制对照表_机械/仪表_工程科技_专业资料。主要用于各类...(1 G # 美制圆锥管螺纹(NPT) 1/8”-27 1/4”-18 3/8”-18 ...
热门文档