文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 交通运输 > ENGINEERING POROSITY IN CERAMICS
侵权投诉

ENGINEERING POROSITY IN CERAMICS

专业资料

Centre for Materials Research

Spotlight ON.. ENGINEERING POROSITY IN CERAMICS By Professor Paolo Colombo– Visiting Professor– Mechanical Engineering Department - UCL

INTRODUCTION

Highly porous ceramics (foams, honeycombs, fibers mats, etc.) have applications in a variety of engineering fields including; filtration (molten metals, particulate from diesel exhaust gases), radiant burners, catalyst supports, biomedical devices, kiln furniture, reinforcement for metal matrix composites, bioreactors, thermal protection systems, supports for space mirrors, components in solid oxide fuel cells, lightweight sandwich structures, heat exchangers, etc. The properties of a ceramic component depend on pore morphology (average size, shape, degree of interconnectivity) and total porosity (Fig. 1). By learning to control porosity, components with a larger range of properties available to engineers can be fabricated.

Prof. Paolo Colombo

By modifying the experimental conditions, it is possible to vary the main characteristics (e.g. mechanical strength, permeability, density,…) of preceramic polymer-derived porous ceramics in a very wide range of values. In Table I are reported data for various properties measured on porous ceramic samples produced using three different processing methods. Table I. Main characteristics of SiOC porous ceramic components obtained following three different processing methods (see Fig. 2 for their morphology).

Property

Bulk density (g/cm3) Porosity (vol%) Average cell size (m) CTE20-1100°C (x10-6 K-1) Thermal conductivity (W/mK) Fig. 1. Change in elastic modulus with the amount of porosity in SiOC ceramic foams obtained from a preceramic polymer

Macrocellular Foams (Fig. 2a) 0.25 to 0.70 68 to 90 100 to 2000 3.75± 0.19 0.104± 0.015 (@ 400°C,= 0.35± 0.02 g/cm3)< 10-16/ cm 1.2 to 12.5

Microcellular Foams (Fig. 2b) 0.26 to 0.60 72 to 88 1 to 185 4.4± 0.20 0.106± 0.032 (@ 20°C,= 0.33± 0.05 g/cm3)< 10-16/cm 2.1 to 18.3 2.9± 0.01 (= 0.31 g/cm3) 1.4 (= 0.31 g/cm3) n.m.

Porous Components (Fig. 2c) 0.45 to 0.95 55 to 80 10 to 500 4.6± 0.15 n.m.

RESULTS It is possible to fabricate a variety of porous ceramics by using preceramic polymers (organic-inorganic polymers whose backbone usually contains Si atoms, which give a ceramic residue through the elimination of organic moieties) and various fabrication methods. Macro-porous ceramics with a high total amount of porosity (55 to 90 vol%) and a range of pore sizes (~1 m– 2 mm) have been obtained, as well as components with graded porosity. 3D interpenetrating composites were produced by infiltration with polymers, carbon precursors or molten metal.

Electrical conductivity Compression strength (MPa) Flexural 0.5 to strength 12.5 (MPa) Elastic 0.4 to 7.6 Modulus (GPa) Fracture 0.15 to thoughness 0.25 (MPam1/2) n.m.= not yet measured

< 10-16/cm n.m. n.m. n.m. n.m.

ENGINEERING POROSITY IN CERAMICS

第1页

你可能喜欢

热门文档

相关文档

  • Advanced Engineering Ceramics

    The article below describes the latest advances in advanced engineering ...It has been shown that porous ceramics that attain both high porosity and ...

  • Defects in Ceramics

    Competence in ceramics 暂无评价 5页 免费 defects in crystals 37页 2财富值 Defects in CVDZnS 暂无评价 5页 2.00元 ENGINEERING POROSITY ... 3页 20...

  • 聚合物发泡方法衍生的制陶方法

    Available online at www.sciencedirect.com Journal of the European Ceramic Society 28 (2008) 1389–1395 Engineering porosity in polymer-derived ceramics Paolo...

  • 12152009 Ceramics

    p 4 Traditional & Engineering g g Ceramics ? Traditional Ceramics (普通陶瓷...40 Sintering g 41 Sintering g temperature p vs p porosity y 42 ...

  • Advanced Ceramics(4)-1

    Decrease grain size in polycrystalline ceramic products ? Minimize porosity ? ...Engineering components Figure 7.1 - Alumina ceramic components (photo courtesy...

  • ENGINEERING MATERIALS

    ENGINEERING MATERIALS_理学_高等教育_教育专区。...Ceramics. A fourth type of material sometime ...Porosity is a measure of voids(open pores) in ...

  • 机械工程英语第二版翻译

    Engineering materials may be further subdivided into: ① Metal ② Ceramics ...At such temperatures, the powders react internally to remove porosity and ...

  • unite1-unite2课文翻译

    Engineering materials may be further subdivided into: ① Metal ② Ceramics ...At such temperatures, the powders react internally to remove porosity and ...

  • 工程英语工程

    Engineering materials may be further subdivided into: ①Metal ①Ceramics ③...At such temperatures, the powders react internally to remove porosity and ...

  • 英语

    Glasses are important engineering materials because of other properties, such ...In general, porosity is detrimental to ceramics properties. ?The silicate ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email