文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 交通运输 > ENGINEERING POROSITY IN CERAMICS
侵权投诉

ENGINEERING POROSITY IN CERAMICS

专业资料

ENGINEERING POROSITY IN CERAMICS

ENGINEERING POROSITY IN CERAMICS

ENGINEERING POROSITY IN CERAMICS

ENGINEERING POROSITY IN CERAMICS

Fig. 2. SEM images of different porous morphologies obtained from a preceramic polymer using various fabrication methods

Very recently, Prof. Mohan Edirisinghe, Dr Eleanor Stride and their research groups at UCL, developed a novel and innovative method of producing high levels of porosity into polymeric bodies, using our expertise in preceramic polymers. It is based on electrospraying a solution of a preceramic polymer in a liquid, under very tightly controlled conditions. This resulted in the formation of microbeads with a size of about 1 to 2 mm and interconnected pores with a dimension in the range of 1 to 7 m approximately (Fig. 3a). In another related development, by employing co-axial electrospraying using a dual nozzle set-up, it was possible to fabricate highly homogeneous hollow spheres with a typical dimension of the order of 1 m (Fig. 3b). The polymeric porous beads were ceramized by heat treatment at 1200°C in inert atmosphere. Both systems are currently being explored for drug delivering applications, both in the preceramic and in the ceramized state.

Fig. 4. SEM image of a porous ceramic on whose surface numerous carbon-based nano-wires/tubes are present (measured SSA = 70 m2/g)

To further extend the range of properties possessed by the porous ceramics, various fillers can be added to the starting preceramic polymer, yielding components that possess electrical conductivity or (ferro)magnetic properties (Fig. 5).

Different porous ceramics produced from preceramic polymers have been successfully tested, or identified for use, in a range of applications; from high temperature thermal insulators, components of hypervelocity impact shields and chemical micro-reactors to aerosol filters and gas adsorption (Fig. 5).

Fig. 3. SEM micrographs of a) a porous microbead and b) hollow

microspheres obtained using electrospraying of a preceramic polymer (both before pyrolysis)

In another recent development, ceramic components with hierarchical porosity (i.e. with micro-, meso- and macro-pores) have been fabricated. A high amount of specific surface area (SSA) can be added to porous ceramic bodies, such as the ones shown in Fig. 2, by various ways, including the deposition of a layer of zeolites or of a meso-porous inorganic coating, by etching, by infiltration with an aerogel, by the addition of suitable fillers or by controlled thermal treatment. A further approach we are investigating consists in the in-situ synthesis of carbon-based nano-wires/tubes on the surface of the porous components (Fig. 4). This occurs directly during pyrolysis, if a catalyst mixed with the preceramic polymer and capable of interacting with the gases (mainly CH4) released during the polymer-to-ceramic transformation is employed. These advanced porous ceramics may find application in separation, gas storage, catalysis and removal of pollutants.

Fig. 5. Examples of possible applications for preceramic polymer-derived porous ceramic components. a) macrocellular heating element; b) microcelllular hypervelocity impact absorber; c) microcellular magnetic component; d) Al-SiOC interpenetrating composite (image courtesy of S. Vaucher, EMPA)

上一页第2页

你可能喜欢

热门文档

相关文档

  • Advanced Engineering Ceramics

    The article below describes the latest advances in advanced engineering ...It has been shown that porous ceramics that attain both high porosity and ...

  • Defects in Ceramics

    Competence in ceramics 暂无评价 5页 免费 defects in crystals 37页 2财富值 Defects in CVDZnS 暂无评价 5页 2.00元 ENGINEERING POROSITY ... 3页 20...

  • 聚合物发泡方法衍生的制陶方法

    Available online at www.sciencedirect.com Journal of the European Ceramic Society 28 (2008) 1389–1395 Engineering porosity in polymer-derived ceramics Paolo...

  • 12152009 Ceramics

    p 4 Traditional & Engineering g g Ceramics ? Traditional Ceramics (普通陶瓷...40 Sintering g 41 Sintering g temperature p vs p porosity y 42 ...

  • Advanced Ceramics(4)-1

    Decrease grain size in polycrystalline ceramic products ? Minimize porosity ? ...Engineering components Figure 7.1 - Alumina ceramic components (photo courtesy...

  • ENGINEERING MATERIALS

    ENGINEERING MATERIALS_理学_高等教育_教育专区。...Ceramics. A fourth type of material sometime ...Porosity is a measure of voids(open pores) in ...

  • 机械工程英语第二版翻译

    Engineering materials may be further subdivided into: ① Metal ② Ceramics ...At such temperatures, the powders react internally to remove porosity and ...

  • unite1-unite2课文翻译

    Engineering materials may be further subdivided into: ① Metal ② Ceramics ...At such temperatures, the powders react internally to remove porosity and ...

  • 工程英语工程

    Engineering materials may be further subdivided into: ①Metal ①Ceramics ③...At such temperatures, the powders react internally to remove porosity and ...

  • 英语

    Glasses are important engineering materials because of other properties, such ...In general, porosity is detrimental to ceramics properties. ?The silicate ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email