· 1620 · 第36卷第11期 2008年11月
硅 酸 盐 学 报
2008年
Vol. 36,No. 11 November,2008
硅 酸 盐 学 报
JOURNAL OF THE CHINESE CERAMIC SOCIETY
部分稳定氧化锆陶瓷的凝胶注模成型工艺
仝建峰,陈大明
(北京航空材料研究院,先进复合材料国防科技重点实验室,北京 100095)
摘 要:用流变学的方法研究了不同条件,如:固相含量、分散剂加入量、烧结助剂、增塑剂等对碱性部分稳定氧化锆(partially stabilized zirconia, PSZ)悬浮体的流变性的影响。结果表明:分散剂含量对悬浮液的流变性能有明显影响,当PSZ固相体积含量为55%时,分散剂加入量(占固相含量的质量分数)应为0.4%。当固相体积含量为50%~56%时,氧化锆碱性料浆呈现剪切变稀行为,具有较低的黏度(在剪切速率为10 s–1时,低于50 mPa s)。氧化锆陶瓷碱性料浆(pH>7)在低的剪切速率(<100 s–1)时,表现为剪切变稀。凝胶注模法生产的PSZ陶瓷坯体的内部结构是均匀的。
关键词:部分稳定氧化锆;凝胶注模;流变特性
中图分类号:O373 文献标识码:A 文章编号:0454–5648(2008)11–1620–05
PREPARATION OF PARTIALLY STABILIZED ZIRCONIA CERAMIC BY AQUEOUS GELCASTING
TONG Jianfeng,CHEN Daming
(The National Key Laboratory of Advanced Composite Materials, Beijing Institute of Aeronautical Materials,
Beijing 100095, China, Beijing 81–3 100095, China)
Abstract: A partially stabilized zirconia (PSZ) ceramic was prepared by aqueous gelcasting. The effects of the zeta potentials, solid loading, dispersant content and milling time on the PSZ suspension were studied. The dispersant content has a remarkable effect on the rheological properties of the suspension. The appropriate dispersant mass fraction for PSZ aqueous slurry with the solid loading of 55% in volume is 0.4%. All suspensions (50% 56% solid loading) exhibit a shear-thinning behavior and relatively low viscosity (less than 50 mPa s, at a shear rate of 10 s–1), which is suitable for casting. The degree of shear thinning and the viscosity at high shear rates increase with the increasing of volume fraction of solid phase. As the milling time is prolonged, the viscosity of the suspension de-creases first, and then a plateau appears and the average diameter remains unchanged. When the milling time is shorter than 20 h, the viscosity of the slurry decreases gradually as the time of milling is increased. After 20 h milling, the viscosity of the slurry tends to be consistent. Therefore, the ball milling time should be equal to or more than 20 h in order to obtain a stable suspension at equilibrium. The appropriate time for casting the slurry (idle time) can be controlled by the amounts of initiator and catalyst added to the slurry as well as by the processing temperature. According to micrographs, the gelcasting green body is homogeneous.
Key words: partially stabilized zirconia; gelcasting; rheologic property
Gelcasting is an attractive new ceramic forming proc-ess for making high-quality, complex-shaped ceramic bodies.[1–6] Gelcasting has many distinct advantages compared with conventional ceramic forming processes such as dry pressing, slip casting, tape casting, and injec-tion molding, and it is a near-net-shape forming process. Its products have high green density, low levels of or-ganic additives and machinability in the green state due to a high strength.[7–15]
Both non aqueous and aqueous solvents can be used in gelcasting. But aqueous systems are preferred be-收稿日期:2008–04–25。 修改稿收到日期:2008–07–03。 基金项目:国家自然科学基金(50672091)资助项目。 第一作者:仝建峰(1972—),男,博士,高级工程师。
cause the use of water as the solvent has many advan-tages, e.g., less departure from traditional ceramic processing and no environmental problems for disposal. In aqueous gelcasting, acrylamide and methylene bis-acrylamide are commonly used to make monomer solu-tions.[11–18]
According to previous studies,[1–21 the composition of monomer solution, the amounts of initiator and catalyst added, and the temperature and humidity of the drying atmosphere are important processing parameters to be controlled for optimum gelcasting. In this work, a par
Received date: 2008–04–25. Approved date: 2008–07–03. First author: TONG Jianfeng (1972–), male, doctor, senior engineer. E-mail: jftong@yahoo.com
氧化锆陶瓷的凝胶注模成型研究_专业资料。研究了氧化锆陶瓷凝胶注模成型工艺中单体、引发剂、固相含量、固化温度对料浆的凝胶固化时间的影响及坯体在干燥、烧成中...
氧化锆陶瓷凝胶注模成形研究_材料科学_工程科技_专业资料 暂无评价
h 浆料 。与其 它精 密 陶瓷 凝胶注模成型工艺不同之处是 在 实验 过程 ...还 为了考察高固相体积分数时含有粗颗粒粉体的氧化锆 浆料的稳定性、了沉降实验...
笔者针对以上的问 题,采用水基凝胶注模成型工艺,以氧化铝粉体为陶 瓷骨料,通过制备稳定的陶瓷料浆,控制各种因素对 其稳定性的影响,成型出密度分布均匀、强度高、...
凝胶注模成型氧化锆陶瓷坯体的性能和显微结构分析_专业资料。研究了通过添加2.6%(质量分数)水溶性高分子聚丙烯酰胺到氧化锆陶瓷悬浮体中能够消除在空气中凝胶注模...
陶瓷凝胶注模成型工艺的研究进展_自然科学_专业资料。有关于凝胶注模的相关文献... 部分稳定氧化锆陶瓷的凝... 暂无评价 5页 2.00 凝胶注模工艺成型氧化铝...
钢铁研究总院功能陶瓷技术研究中心 摘 要 系统地介绍了凝胶注模成型工艺十余年...使用该工艺已成功制备出氧化 铝、 熔融石英 、 氧化锆 、 碳化硅 、 氮化硅 ...
本文对陶瓷凝胶注模成型的原 理、工艺、成型体系、... 英文个人简历模板 创意简历模板汇集 推理型题分析与... 部分稳定氧化锆陶瓷的凝... 暂无评价 5页 2...
matete 教授 等提出了 凝胶 注模成型技术( Gelcast ing ) [ 7, 8] , 首次 将传 统陶瓷 工艺 与聚 合物 化学有机地结合起来, 开创 了在陶瓷 成型工 艺...
热门文档