文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 能源/化工 > surfactant controlled switching of water-in-oil wetting behaviour of porous silica films grown at oi
侵权投诉

surfactant controlled switching of water-in-oil wetting behaviour of porous silica films grown at oi

表面活性剂在油田的应用

J. Chem. Sci., Vol. 120, No. 6, November 2008, pp. 637–643 © Indian Academy of Sciences.

Surfactant controlled switching of water-in-oil wetting behaviour of porous silica films grown at oil–water interfaces

MANISH M KULKARNI, RAJDIP BANDYOPADHYAYA1 and ASHUTOSH SHARMA*

Department of Chemical Engineering, Indian Institute of Technology Kanpur, Kanpur 208 016, 1

Present address: Department of Chemical Engineering, Indian Institute of Technology Bombay, Powai, Mumbai 400 076

e-mail: rajdip@che.iitb.ac.in; ashutos@iitk.ac.in

Abstract. Selective permeation of oil and water across a porous medium, as in oil recovery operations, depends on the preferential wetting properties of the porous medium. We show a profound influence of surfactants in wetting of porous media and thus demonstrate a new route for the control of water-in-oil wetting of porous substrates by changing the concentration of surfactants in an aqueous sub-phase below the substrate. This strategy is employed to engineer partial reversible wetting transitions on a porous sil-ica film. The film itself is grown and stabilized on a flat, macroscopic interface between an oil phase and an aqueous sub-phase. On increasing the surfactant (CTAB) concentration in the sub-phase, contact angle of a water drop (placed on the oil side of the film) changes from 140° to 16° in 25 min by diffusion of the surfactant across the porous film. On further replacement of the sub-phase with pure water, diffusion of the surfactant from the water drop back to the sub-phase was slower, increasing the contact angle in the process from 16° to 90° in 2 h. Wettability control by a cationic surfactant (CTAB) was found to be much faster (6 deg/min) than that offered by an anionic surfactant, SDS (0 05 deg/min). Switching of the sur-face wettability due to the surfactant diffusion may have implications in oil–water separation, chemical bed reactors and microfluidic devices.

Keywords. Wetting control; porous substrate wetting; porous silica film; surfactant mediated wetting; oil–water contact angle.

1. Introduction

Spreading of liquid on a porous solid1 and under-standing the mechanics of the flow inside porous body are important in adsorbers and reactors with porous packings.2,3 The Spreading and penetration of liq-uids and movement of the three phase (solid–liquid–air) contact lines on porous surfaces like paper, fabric, etc have also been studied extensively.4,5 Reversible switching of hydrophilic–hydrophobic characteristics of surfaces is desired in many applications. Various methods like electrowetting,6 chemical surface modi-fication,7 conformational and photo-induced transi-tions have been reported for dynamic control of surface wetting. Most of these works are concerned with the control of wetting in air–water–surface sys-tems by manipulating the surface properties of a non-porous solid surface. In case of control by elec-trowetting, the solid surface needs to be electrically active. However, in many practical applications the solid surface properties cannot be readily altered.

Dedicated to Prof. C N R Rao on his 75th birthday *For correspondence

In many important applications, such as in oil re-covery operations, selective permeation of oil and water across a porous medium depends on the pref-erential wetting properties of the porous medium. Further, wetting characteristics of porous rocks play a profound role in displacement of oil by water from these surfaces. We show a profound influence of surfactants in wetting of porous media and thus demonstrate a new route for the control of water-in-oil wetting of porous substrates by changing the concentration of surfactants in an aqueous sub-phase below the substrate. Towards this end, we employ a model system of a porous silica film, which was grown and stabilized at a flat, macroscopic oil–water interface. We report a new surfactant mediated con-trol of the wetting characteristics of such a porous wall. This is shown by a transition in the contact an-gle of a water drop placed on the oil-side (like hep-tane) of the film.

Use of a liquid–liquid interface to grow metallic nanocrystalline films has been described in the semi-nal works of Rao et al.8,9 Similarly, Faget et al10 synthesized mesoporous silica films at an oil–water

637

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email