文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > Design of high efficiency solar cells by photoluminescence studies
侵权投诉

Design of high efficiency solar cells by photoluminescence studies

parts of the complex structure. The two diagnostic devices to be described here simulate the p-type emitter and the n-type base of the final cell. To speed process development, diagnostic isotype double heterostructures (DH)273were fabricated under a variety of growth conditions. These DH devices are similar to the solar cell base (Fig. 2) and emitter (Fig. 3) but are much simpler to make than a finished solar cell. Because no contacts are required and the structures are quite simple, large numbers of DH devices can be made in fairly short times. The best growth conditions for various components can be determined from the measurements to be described here.

EMITTER DIAGNOSTIC DEVICE p- AI,,Q;%,As I

Window THICKNESS

p-GaAs

4x10’’

0.3 micron

BASE DIAGNOSTIC DEVICE Figure 3: Schematic diagram of the diagnostic double heterojunction used to analyze electron recombination in the emitter. n - GaAs Active Layer d

0.3 microns

The photoluminescence (PL) lifetime of an isotype DH structure can be decomposed into two primary components -- bulk and interface recombination. The bulk lifetime may be further decomposed into two components -- the intrinsic radiative lifetime and the nonradiative or Shockley-Read-Hall lifetime. The total bulk lifetime ZB may be written as:

n- AI Ga As 0.3 0.7

where the radiative lifetime TRis given by: Figure 2: Schematic diagram of the diagnostic double heterojunction used to analyze hole recombination in the base.

Time-resolved photoluminescence (PL) measurements produce data from which the bulk minority carrier lifetime ( 2 ) and the interface recombination of the passivating AI,Gal.,As layer can be determined. The measurements were performed using the SERl time-resolved single photon counting technique’ described earlier. Once the best growth conditions for the various components have been established, the more complex cell structures can be fabricated following the various component recipes. MINORITY-CARRIER PARAMETER CHARACTERIZATION

Here B is the radiative recombination coefficient which is specific to a semiconductin material and is about~ x I O -~cm3 s-l for GaAs.5j Here N is the O majority carrier concentration and TNRis the bulk nonradiative lifetime. In the linear model of recombination, the radiative lifetime is the maximum value of the bulk lifetime (negligible nonradiative lifetime in the bulk). The solution of the time dependent diffusion equation for the DH structure is com lex and may be expressed as a Fourier series.P18 The asymptotic value (t>> d*/2D) of the PL lifetime in a DH structure with an active layer thickness d, interface rec

ombination velocity s, and minority carrier diffusion coefficient D is then given by:

Two or more DH structures of different active layer thickness were grown, and the interface recombination velocity S and the bulk lifetime‘c for the diagnostic devices was determined. These parameters appeared to vary greatly with growth temperature as will be shown. A large number of fabrication runs were performed over temperatures ranging from 700°C to 800°C and the was data analyzed in a manner which will be described later in this paper.

1 12=s . ZPL

TB

d

(3)

By growing devices that are identical, except for the active layer thickness d, Eq. 3 can be solved to find S. If 2S/d becomes small and bulk nonradiative recombination becomes negligible, then the PL lifetime becomes the radiative lifetime. Thus in the linear model:

433

Design of high efficiency solar cells by photoluminescence studies

上一页第2页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email