文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 材料科学 > 2.2.14 Cr-Mo-V-Ti-B steel
侵权投诉

2.2.14 Cr-Mo-V-Ti-B steel

Ref. p. 99]

2.2.14.3 Creep rupture strength

2.2.14 Cr-Mo-V-Ti-B steel 97

The creep rupture strength of 20CrMoVTiB4-10 is shown in Fig. 107. The analysis, from which the data in the figure are derived, was carried out as part of the activities of the European Creep Collaborative Committee and additional details can be found from their published data sheets [1].

2.2.14 Cr-Mo-V-Ti-B steel

10864

Stress [MPa]

2

108

6×10

Temperature[°C]

Fig. 107. Creep rupture strength data of 20CrMoVTiB4-10

The creep rupture properties have been obtained by analysis of bar material with sizes of 19 - 190 mm. The tensile properties of the material covered the range 680 - 900 Nmm-2 for Rp0.2 and 830 - 1040 Nmm-2 for Rm. The test data were from 75 heats with test temperatures of 450 - 700 °C with the majority in the range 500 - 600 °C. The distribution of test durations are shown in Table 69.

Table 69. Distribution of test durations used to derive the stress rupture properties of 20CrMoVTiB4-10

>100,000 h <10,000 h

20,000 h 30,000 h 50,000 h 70,000 h 100,000 h

513 (26) 81 (11) 94 (11) 44 (8) 15 (2) 1 (2) 8 (2) ( ) Denotes unbroken tests

The data were assessed using the ISO 6303 procedure and the following master equation was derived: P(σ ) = (log(tr*) log(ta)) / (T Ta)r = a + b(logσ) + c(logσ)2 + d(logσ)3 + e(logσ)4

where P(σ) is the creep rupture parameter, tr* is the predicted rupture time in hours, T is the absolute temperature and -2. The remaining symbols are constants with the following values:

log (ta) Tar 4.465617180 8.252388000 5.7271780971.762619853 0.20331820852.2.14.4 Creep properties from research papers

At the sizes found in typical bolting applications after oil quenching from temperatures in the range 970 - 990 °C the microstructure of Durehete 1055 consists of fine grained bainite. Subsequent tempering in the range 680 - 720 °C produces a dispersion of V4C3 precipitates. The alloy derives its creep strength from these precipitates together with solid solution strengthening from chromium and molybdenum. The optimum creep properties are obtained by a vanadium addition of about 0.7%, which is close to the stoichiometric level for the carbon level of 0.2% in this alloy.

Landolt-Börnstein New Series VIII/2B

上一页第2页

你可能喜欢

热门文档

相关文档

  • DIN EN 970 EN 1997_03

    Analysis of aluminium ... 暂无评价 36页 免费 2.2.14 Cr-Mo-V-Ti-B st... 暂无评价 4页 1下载券2014 Baidu 使用百度前必读 文库协议...

  • DIN EN 970 EN 1997_03

    Analysis of aluminium ... 暂无评价 36页 免费 2.2.14 Cr-Mo-V-Ti-B st... 暂无评价 4页 1下载券2014 Baidu 使用百度前必读 文库协议...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email