文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > 2014-OE-Super-Nyquist-WDM transmission over
侵权投诉

2014-OE-Super-Nyquist-WDM transmission over

Super-Nyquist-WDM

2014-OE-Super-Nyquist-WDM transmission over

Fig. 4. Experimental setup.

After the modulated WDM signals from three rails were fed into the polarization multiplexing emulators (PMEs), they were combined by WSS. Each channel power of the WDM signals was automatically equalized by the WSS with power monitor. Consequently, we obtained 201-channel 25-GHz-spaced super-Nyquist-WDM 30-Gbaud duobinary-pulse-shaped DP-QPSK signals, resulting in a spectral efficiency of 4 bit/s/Hz assuming a LDPC-based SD-FEC with 20% overhead [12].

For multi-core fiber (MCF) transmission, the 201-channel WDM signals were launched into a specially configured seven-fold recirculating loop consisting of a span of 45.5-km seven-core fiber, a seven-core EDFA, external gain-flattening filters (GFFs), and optical switches (SWs). The seven loops were synchronously operated as reported in [13]. The seven re-circulating loops shared a common load switch that launched identical copies of the WDM signals into each of the loops through a power splitter with over 75-symbol delay between cores for the signal decorrelation. After amplification by the seven-core EDFA with external GFFs, the signals were launched into the cores of the 45.5-km MCF. The output signals from one core were sent to the re-circulating loop input of the next core, in a cyclic fashion. The core-to-core configuration can average out variations in span loss, dispersion, and other component imperfections [13]. Two WSSs and two single-core EDFAs were inserted at input of the fourth and seventh cores for gain equalization, and the gain flatness was automatically managed by the WSS at input of the seventh core. A polarization scrambler was inserted at the input of the fifth core.

The transmitted signals were received by a digital coherent receiver after pre-amplification and channel selection with an optical band-pass filter (OBPF) with a bandwidth of 1 nm. Electrical signals from the receiver were stored in sets of 1M samples by using a four-channel digital oscilloscope operating at 50 Gsample/s. The stored data were processed offline by DSP as follows: The received signals were re-sampled to two sample/symbol. After square-root duobinalry-pulse shaping and dispersion compensation in the frequency domain, polarization demultiplexing and signal equalization were performed by half-symbol-spaced FIR filters with 80 taps, which were adapted by the decision-directed least-mean square (DD-LMS) algorithm [14]. After MLSE, the symbols were decoded. 4.2 Measured back-to-back performance of super-Nyquist-WDM signals

Figure 5 shows optical spectra of 25-GHz-spaced super-Nyquist-WDM 30-Gbaud Nyquist-pulse-shaped and duobinary-pulse-shaped DP-QPSK signals. We can see the significant spectral overlapping in Nyquist-pulse-shaped WDM signals. On the other hand, by using

#200695 - $15.00 USD(C) 2014 OSAReceived 7 Nov 2013; revised 4 Jan 2014; accepted 7 Jan 2014; published 13 Jan 201427 January 2014 | Vol. 22, No. 2 | DOI:10.1364/OE.22.001220 | OPTICS EXPRESS 1225

上一页第6页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email