文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 材料科学 > Thermal_Mechanical_Decoupling_by_a_TIM
侵权投诉

Thermal_Mechanical_Decoupling_by_a_TIM

(302) 834-2100 (302) 834-4021 (Fax)

VI. The effect of the extending filler system

Although silicone rubber has excellent thermal stability and elasticity, its thermal conductivity is too low (0.2W/mK) for most TIM applications. High thermal conductivity extending fillers are generally mixed into the silicone rubber matrix to increase the thermal conductivity2. This method can increase thermal conductivity values for a silicone TIM by greater than an order of magnitude. The extending filler must meet the following requirements: 1) High thermal conductivity. 2) Small particle size -- Small particle size is critical for mixing so that the elasticity of the matrix is not compromised. Most of the extending fillers are of the micron order. 3) Compatibility with the silicone rubber. 4) Electrically insulative or conductive -- depending on the application.

A. Filler content

In an electronic application, the PCB components continuously give off heat. This heat is conducted through the TIM, such as Arlon’s Thermabond® adhesive, to the heat sink. A highly thermally conductive TIM is beneficial to the PCB because the thermal conductivity of the TIM (usually <10W/mK) is much lower than that of the heat sink (usually aluminum, Tc>200W/mK).

In order to obtain higher thermal conductivity for the TIM, extending fillers are added to the silicone rubber matrix. It has been found that the compound may crumble at filler content higher than a certain value. Additionally,

processing properties of the uncured compound and the mechanical properties of the cured TIM also change with increasing filler content. Even if there are no active sites on the extending filler surface for a reinforcement contribution, the mechanical properties of the cured TIM can change due to the hydrodynamic effect4, 9. In particular, the durometer and shear modulus increase with increased extending filler content.

B. Filler Surface Activity

The surface properties of the extending filler profoundly affect the interaction between the extending filler and the silicone polymer. The interaction between the extending filler and silicone affects interfacial thermal resistance. If the interaction between the extending fillers and silicone increases, the wetting of the silicone on the filler surface is better and, consequently, there is less interfacial thermal resistance. The interaction between the extending filler and the silicone also depends on the chemical structure of the silicone. The backbone of silicone rubber is always repeating units of silicon-oxygen, the side and end groups can be methyl, vinyl, phenyl, hydrogen, trifluoropropyl, or hydroxyl. These groups affect the interaction between the extending filler and the polymer.

As previously discussed, the extending fillers also have a reinforcing effect on silicone. If the interaction between the fillers and the silicone increases, the reinforcing effect of the extending filler becomes more significant.

上一页第5页

你可能喜欢

热门文档

相关文档

  • TDA7496_03中文资料

    F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 元器件交易网...

  • TDA7495S_04中文资料

    N.C. INR D99AU1016 THERMAL DATA Symbol Rth j-...decoupling Mute time constant Output DC decoupling ...MECHANICAL DATA Multiwatt15 (Vertical) 0016036 J ...

  • DFIG的SVM_IPC与SVM_DPC比较_赵梅花

    ( 1. Department of Mechanical and Electrical Engineering,Luoyang Institute of...( SVMIPC ) was proposed,which indirectly achieved decoupling control between ...

  • 01_ZF_Sachs_Product_Information_PC_A_Clutch_Systems...

    enough to handle thermal loads and facing wear. ...The mechanical subsystem is located inside the ... excellent vibration decoupling thanks to adapted ...

  • DecouplingContro_省略_ckingManipulator_Yon

    In this paper, the coupling between two inputs is analyzed, with the imbalance of drive wheel and mechanical errors under consideration. A decoupling ...

  • TDA7496

    F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 TDA7496 ...

  • TDA2009A

    (1) Frequency Stability Input DC Decoupling Larger...BUILD-IN PROTECTION SYSTEMS THERMAL SHUT-DOWN The...12 TDA2009A MULTIWATT11 PACKAGE MECHANICAL DATA DIM...

  • BenQ joybook_A53[1]

    SW4 for mechanical request CON9 pin27 and pin30...Thermal Sensor NB Thermal Sensor P3 01 Battery ...DECOUPLING 17--SB600-STRAPS 18--RTS5158 & 3in1...

  • 4. FC300 mechanical and Electrical installation

    4. FC300 mechanical and Electrical installation_电子/电路_工程科技_专业资料...Decoupling plate for power cables Confidential / Property of 27 February, ...

  • Intel内部笔记本散热设计培训 2008[1]

    Thermal/Mechanical Team CPU FET FET Vcc core decoupling Measure V Measure V...Pre-Test Preparation --Apply new thermal interface material (TIM) to the ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email