文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电力/水利 > 洁净管道和管件焊接程序标准作业指导书
侵权投诉

洁净管道和管件焊接程序标准作业指导书

洁净管道和管件焊接程序标准作业指导书

Overlapping 焊接重叠过多

Excessive penetration (penetration may not exceed 10%-15% of nominal wall thickness) 额外的焊接成型部分(不能超出一般管壁厚度的10%-15%)

The weld collar is better with minimum discoloring. A light yellow or straw-coloured discoloration is permissible. Discoloration like dark brown to black is poor forming.

焊缝最好是只有最小的颜色改变。亮黄或淡黄色是允许的。黑褐色或黑色是很差的形成色。 Not continuously welded 不连续的焊接

The welding bead must have a uniform width around the entire circumference of the seam. There may be no cracks, discontinuities or hollows.

焊缝成型的鳞片必须是围着整个焊缝的焊道形成统一的宽度。没有裂缝、中断或凹洞。 The realization of the weld will assure that the finishing surface of the weld will be free of pores, cracking, bubble, crystals or any other rugosity or surface irregularity, through the regulation of the weld current, purge gas, etc.

通过调整焊接的电流、送气等参数,使得焊接结果要保证外表面的最终成形没有气孔、裂纹、 气泡、小晶粒或其他褶皱或表面不规则。

The weld should present regularity of pulses gaps on four levels or sectors. Each pulse should overlap or cover as minimum a 50% of the previous pulse surface. The mechanical resistance traction of the weld made, result optimum when the superposition of pulses is approximately a 75% of the area.

焊接应沿着四个断面均呈现出一种有规律的脉冲波纹,每一个波纹至少有50%的部分被上一 个波纹覆盖着,露出的部分是小于50%的,否则将不可接受。在焊接过程中,通过焊接机械 阻力的牵制,使波纹的覆盖接近75%的理想结果。

As a general rule, the collar width should be approximately twice the pipe wall’s thickness. Weld collar width should be uniform throughout the pipe wall. For pipes of 1,2 mm. thickness, weld collar should be made by an only run and weld collar base should be approximately from 2 mm. up to 4 mm. width, and present a regular width on the four sectors.

作为一般的原则,焊缝的宽度大约为管道厚度的两倍。焊缝的宽窄沿管道一圈要做到基本一 致相同。例如,管道厚度为1.2mm,焊缝只能是一个唯一的一圈,焊缝的宽度大约2mm 到 4mm 宽。在四个断面上的呈现一致的宽度。

All the pipe extremes, accessories and valves will be carefully aligned to reduce as much as possible the not-lined. The not-lined mustn’t exceed over the 15 % of the wall thickness. 所有的管接头、附件和阀门等在焊接时都要非常小心地尽量排列对齐,以减少错位偏心的发 生。错位偏心不能超过15%的壁厚。

The internal concavity of the weld collar mustn’t exceed from the 10% of the pipe wall thickness. The external concavity of the weld collar mustn’t be higher from the 15% of the pipe wall thickness.

焊缝向内凹陷,不能超过10%的管道壁厚;向外凸起不能大于15%的管道壁厚。 Automatic Weld: 自动焊接:

上一页第9页

你可能喜欢

  • 管件尺寸表
  • 管件重量表
  • 阀门知识简介完全版下
  • 压力管道标准
  • 管道布置图
  • 弯头放样方法
  • 国标美标尺寸对照表

热门文档

相关文档

  • 管道焊接作业指导书

    管道焊接作业指导书 1 一般规定 1.1 管道工程的... b 除定型管件外,其他任意两焊缝间的距离不小于 ...用易挥发的溶剂清洗油污,应保持接头处的干燥与洁净...

  • 管道焊接作业指导书

    管道焊接作业指导书 陕西正丰建设工程有限公司 陕西正丰建设工程有限公司 正丰 零一一年五 二零一一年五月三日 管道焊接作业指导书一、焊工安全操作规程 焊工安全操作...

  • 管道电焊作业指导书编号

    管道电焊作业指导书工步 1)验证焊 前: 程序/方法 程序 方法 质量标准 编号:Y2-7.5.1.1-2( ) 编号环境影响 对策 安全风险 对策 管道直径和材料/配件 ...

  • 管道焊接作业指导书

    焊接作业指导书 一、编制依据 1、 《油气长输管道工程施工及验收规范》 2、 ...2、工程开工初期管道焊接质量控制程序 为了保证管道开工初期的焊接质量,使焊工充分...

  • 地下管道焊接作业指导书

    地下管道焊接作业指导书_电力/水利_工程科技_专业...管件、阀门在安装前,按设计要求核对其规格、材质、...预制完毕应检 查内部洁净度,并临时封闭管口,同时按...

  • 长输管线组焊施工作业指导书1

    ***工程南线段管道组焊作业的指导性文件,为管道组焊作业规范化、标 准化、系统...洁净、无开裂、无锈蚀、油污及其它污物;具有良好的工艺性 能和成型能力; 3、...

  • 大口径管道焊接作业指导书

    大口径管道焊接作业指导书_电力/水利_工程科技_专业资料。CSPC NANHAI ...2.3 PR-8710-8100-0025 焊接程序 WELDING PROGRAM Rev.00 2.4 PR-8710-...

  • 循环水管道焊接作业指导书

    惠民新材料有限公司热电厂(4*330MW)机组工程循环水管道焊接作业指导书 一、工程...施工方法、步骤及作业程序 5.1 手工电弧焊:采用多层多焊道两人对称施焊,先在...

  • 6压力管道焊接作业指导书

    XXX 公司 压力管道焊接作业指导书(XXX-2012) 文件编号:XXX-2012 压 力管 道...-15- XXX 公司 压力管道焊接作业指导书(XXX-2012) 管材与管件焊接工艺参数 表...

  • PE聚乙烯管道热熔焊接作业指导书

    电焊机安全操作规程 2012 年 1 月 4 日 1 PE 聚乙烯管道焊接作业指导书一...4、5按照操作程序操作电焊机至输入焊接参数位置,用手 动方式(参数由管件自身...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email