Comparison Of Failure Criteria For Jointed Rock Masses 节理岩体破坏准则比较
zoning technique used in FLAC ensure that plasticcollapse and flow are modelled accurately. Apartfrom several built-in constitutive models, FLACalso contains the powerful built-in programminglanguage FISH with which the users can writetheir own functions to extend FLAC's usefulnessand even implement their own constitutivemodels. The grid used for simulating the triaxialtest sample is shown in Figure 1. Only symmetricquarter of the total test sample is simulated in thenumerical analysis since stress-state will beisotropic because of the equivalent uniformproperties assumed for the jointed rock sample.

Figure 1. Grid used to simulate triaxial test
specimen of rock in numerical analysisSpecial FISH functions are written to explicitlyincorporate both Hoek and Brown andRamamurthy’s failure criteria as subroutinesalong with the Mohr-Coulomb model in theprogram. These FISH functions adjust the valuesof cohesion and friction angle at each step withvariation in confining pressure, using the m and sparameters in case of Hoek and Brown criterionand B and α in case of Ramamurthy’s criterion.
2.Numerical analysis of triaxial compressionNUMERICAL EXPERIMENTS
tests on intact and jointed rocks was first taken up.Three different intact rocks for which theexperimental stress-strain curves were reported inthe literature were selected for the analysis.
Intact Kota sandstone with linear stress-strainresponse (Yaji, 1984), jointed Agra sandstone
(joints inclined at 70° with joint frequency of 39per meter depth) exhibiting slightly non-linearstress-strain response (Arora, 1987) and GypsumPlaster (block jointed sample with two sets ofjoints inclined at 30°/60° with joint frequency of20 per meter depth) exhibiting highly non-linearstress-strain response (Brown and Trollope, 1970)were selected and their stress-strain responses atdifferent confining pressures were predicted fromnumerical analysis. The properties of the intactrocks are given in Table 1. The c and φ valueslisted in the table are the initial strengthparameters, which are eventually modified uponloading in the analysis at each time step.
The parameters αi and Bi for Ramamurthy’scriterion are given in Table 2 and mi and si forHoek and Brown parameters are given in Table 3.These parameters are for the laboratory size intactrock specimens and in case of jointed rocks, theparameters should be calculated using equations3, 4, 7 and 8. RMR values listed are for the rockmass, calculated as per Bieniawski (1973) basedon uniaxial compressive strength, drill corequality, spacing and condition of discontinuities.Ground water is not present in the samples.Table 1 Properties of intact rocks
Type of rockσci
kPa
kPaφ
Intact Kota
sandstone701144
Sandstone1101951
Gypsum
Plaster
21035
Table 2 Ramamurthy’s parameters for different
rocks.
Ramamurthy’s Parameters
Rock Type
fαi
iIntact Kota
sandstone00.882.2
Sandstone61.50.753.35
Gypsum
Plaster
6330.862.05
International Journal of Rock Mechanics & Mining Sciences 38 (2001) 591–598 Technical Note A stress–strain relation for jointed rock masses Fa-quan Wu...
model for hydraulic fracturing of jointed rock masses during HDR stimulation ...Comparison of the analysis results with the data recorded during the ...
for slope stability analysis in situations where the failure mechanism is not...of the strength and deformation characteristics of rock masses are required ...
Deformability characteristics of jointed rock masses under uniaxial compression_专业资料。Itrainlorao nn cec n ehooy221)1-21nenta ulfoJn MiigSineadTcnlg2(...
the joints and rock material respective criteria. ...comparison with a characteristic length of the ...Macroscopic Failure Condition for Jointed Rock Mass...
Macro-mechanical properties of columnar jointed basaltic rock masses 隐藏>> JCn.ot nvTcn1(011:1324 .etSuhUi.eho.21)824—19DoI010/l710105:4:1.07s17...
Failure Properties of Fractured Rock Masses as ...for the failure criterion of a jointed rock mass...the joints and rock material respective criteria. ...
for the failure criterion of a jointed rock mass...the joints and rock material respective criteria. ...A comparison is performed on an illustrative ...
(2005)08–1275–08 ANISOTROPIC YIELD CRITERION FOR JOINTED ROCK MASSES BASED...Formulation of anisotropic failure criteria incorporating a microstructure tensor[...
3 MECHANICAL MODELS AND FAILURE CRITERIA Much effort has been put into ...An anisotropic strength criterion for jointed rock masses (Chen et al., ...
热门文档