文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 物理 > ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling
侵权投诉

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

ALE3D模拟慢烤

In order to demonstrate this capability, we investigate model problems based on the Scaled-Thermal-Explosion-Experiment (STEX) which is used to quantify the violence of thermal explosions under carefully controlled conditions2. In these experiments, a thin-walled vessel (tube) with heavily reinforced end flanges is filled with a high-explosive material (see Figure 1). The vessel is heating by several radiant heater at either a slow cookoff rate (SCO) of a few oC per hour or a fast cookoff rate (FCO) of a few oC per minute. Measurement of the tube expansion in the course of the heating and subsequent explosion allows for accurate and quantitative characterization of the explosion violence. The experiment focuses on deflagration and fragmentation phenomena which is influenced by chemical decomposition, thermal damage and dynamics gaps during the heating

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

phase.

FIGURE 1. Schematic of geometry and 1D model of STEX cookoff test.

Two modeling approaches are employed for the gap. In the first model, slide surfaces bound the air in the gap between the steel pipe and the interior explosive. This approach allows heat transport by both thermal conduction and radiation as would be present in fast cookoff. In the second approach, a mixed material model is employed for the air in the gap. It accommodates thermal conduction across the gap as would be encountered in slow cookoff. In order to demonstrate these approaches we simplify the geometry of the problem by considering a one-dimensional “wedge” of the central portion of the vessel.

MODELS

Initial ALE3D simulations of the STEX cookoff experiment showed excellent agreement for the time to explosion and thermal profiles, but model wall expansions during the heating phase were much larger than measured values1. It is important to obtain accurate mechanical results during the heating phase since the mechanical state of the system at ignition has a strong effect on violence. Possible contributing factors to the above-mentioned discrepancy include the numerical errors associated with the integration of the momentum equation, the numerical representation of the gap, and errors in the chemical decomposition model. Here we focus on improvements in the integration of the momentum equation and the treatment of gaps.

Consider the slow cookoff of LX-10 (HMX, 95%, and VITON, 5%), in a 1D STEX vessel. The vessel is made of 4130 steel, has a 5.08 cm ID and a wall thickness of 0.406 cm. The decomposition of LX-10 is represented by a multi-step reaction model and a power-law expression is used to represent the laminar burn of the HE after ignition. Standard models are used for the strength and equation of state of the LX-10 solid and gas species, air, and steel [4]. The surface temperature of the vessel is increased at the rate of 2oC/hr until explosion. The method of slide surfaces is used to represent the closing of a 1.0 mm gap between the steel and the outside radius of the HE. The gap closes as the HE expands inside the steel due to thermal expansion and the formation of decomposition gases.

Figure 2 shows the zoning for our two dimensional cylindrical wedge that includes LX-10, the steel case and the intervening slide-surface gap. In this case the width of the gap is 0.2 mm.

ALE3D chemical, mechanical and thermal modes have been developed to model the cookoff of LX-10 in the STEX test. The decomposition of HMX in the LX-10 is modeled by a four-step, five species chemical kinetics model. The first two steps are endothermic and the final two steps are exothermic as indicated in Table 1.

A B r1 = Z1exp( -E1/RT) A (1)B C r2 = Z2exp( -E2/RT) B (2)

上一页第2页

TOP相关主题

你可能喜欢

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email