运算放大器AD623英文资料
AD623
Amplifying Signals with Low Common-Mode Voltage
Because the common-mode input range of the AD623 extends0.1V below ground, it is possible to measure small differentialsignals which have low, or no, common mode component. Fig-ure 50 shows a thermocouple application where one side of theJ-type thermocouple is grounded.

The voltages on these internal nodes are critical in determiningwhether or not the output voltage will be clipped. The voltagesVA1 and VA2 can swing from about 10 mV above the negativesupply (V– or Ground) to within about 100 mV of the positiverail before clipping occurs. Based on this and from the aboveequations, the maximum and minimum input common-modevoltages are given by the equationsVCMMAX = V+ – 0.7 V – VDIFF × Gain/2VCMMIN = V– – 0.590 V + VDIFF × Gain/2
These equations can be rearranged to give the maximum possibledifferential voltage (positive or negative) for a particular common-mode voltage, gain, and power supply. Because the signals on A1and A2, can clip on either rail, the maximum differential voltagewill be the lesser of the two equations.|VDIFFMAX| = 2 (V+ – 0.7 V – VCM)/Gain|VDIFFMAX| = 2 (VCM – V– +0.590 V)/Gain
However, the range on the differential input voltage range is alsoconstrained by the output swing. So the range of VDIFF may haveto be lower according the equation.
Input Range ≤ Available Output Swing/Gain
For a bipolar input voltage with a common-mode voltage that isroughly half way between the rails, VDIFFMAX will be half thevalue that the above equations yield because the REF pin will beat midsupply. Note that the available output swing is given fordifferent supply conditions in the Specifications section.The equations can be rearranged to give the maximum gain for afixed set of input conditions. Again, the maximum gain will bethe lesser of the two equations.
GainMAX = 2 (V+ – 0.7 V – VCM)/VDIFFGainMAX = 2 (VCM – V– +0.590 V)/VDIFF
Again, we must ensure that the resulting gain times the inputrange is less than the available output swing. If this is not thecase, the maximum gain is given by,
GainMAX = Available Output Swing/Input Range
Also for bipolar inputs (i.e., input range = 2 VDIFF), the maxi-mum gain will be half the value yielded by the above equationsbecause the REF pin must be at midsupply.
VOUT2V
Figure 50.Amplifying Bipolar Signals with Low Common-Mode Voltage
Over a temperature range from –200°C to +200°C, the J-typethermocouple delivers a voltage ranging from –7.890mV to10.777mV. A programmed gain on the AD623 of 100 (RG =1.02 k ) and a voltage on the AD623 REF pin of 2 V, results inthe AD623’s output voltage ranging from 1.110V to 3.077Vrelative to ground.
INPUT DIFFERENTIAL AND COMMON-MODE RANGEVS. SUPPLY AND GAIN
Figure 51 shows a simplified block diagram of the AD623. Thevoltages at the outputs of the amplifiers A1 and A2 are given bythe equations
VA2 = VCM + VDIFF/2 + 0.6 V + VDIFF × RF/RG = VCM + 0.6 V + VDIFF × Gain/2VA1 = VCM – VDIFF/2 + 0.6 V – VDIFF × RF/RG = VCM + 0.6 V – VDIFF × Gain/2

POS SUPPLY
65
VThe maximum gain and resulting output swing for differentinput conditions is given in Table IV. Output voltages are refer-enced to the voltage on the REF pin.
For the purposes of computation, it is necessary to break downthe input voltage into its differential and common-mode compo-nent. So when one of the inputs is grounded or at a fixed voltage,the common-mode voltage changes as the differential voltagechanges. Take the case of the thermocouple amplifier in Figure50. The inverting input on the AD623 is grounded. So when theinput voltage is –10 mV, the voltage on the noninverting input is–10 mV. For the purposes of signal swing calculations, this inputvoltage should be considered to be composed of a common-modevoltage of –5 mV (i.e., (+IN + –IN)/2) and a differential inputvoltage of –10 mV (i.e., +IN – –IN).
NEG SUPPLY
Figure 51. Simplified Block Diagram
REV. C–15–
AD620中文资料 20页 1下载券仪表放大器AD6...本文介绍的可编程增益运算放大器 AD623 很好 的 实现 了这 一功 能 .实 ...
系统中的应用_计算机硬件及网络_IT/计算机_专业资料...奉文介绍的可编程增益运算放大器AD623 禳好驰实褒... 英文刊名: 年,卷(期): 被引用次数: 王建新, ...
AD623单电源_工程科技_专业资料。介绍了AD623单电源的使用方法及设计要点AD623 单电源、电源限输出仪表放大器的原理及应 摘要: 介绍了美国 ADI 公司最新推出的...
AD623仪表放大器在数采系统中的应用-CN_信息与通信_工程科技_专业资料。AD623维普资讯 http://www.cqvip.com 传感器与仪器仪表 仪表放大器 A63D2 在数采系统...
运算放大器实战入门(下)_信息与通信_工程科技_专业资料。运算放大器实战入门(下)运算放大器实战入门( 运算放大器实战入门(下) 云南大学信息学院:何乐生 2010.4...
仪表放大器的应用技巧 长期以来,为仪表放大器供电的传统方法是采用双电源或双极性电源,这具有允许正负输入摆幅和输出摆幅的明显优势。随著元器件技 术的发展,单 ...
仪表运算放大器型号列表_信息与通信_工程科技_专业资料。仪表运算放大器——型号列表制造商 TI 公司 产品类别 仪表运算放大 器 产品型号 INA110KP INA111AP INA114AP...
仪表放大器的正确使用方法_电子/电路_工程科技_专业资料。非常好的资料...由于采用运算放大器,仪表放大器电路 的输入缓冲级 A1 和 A2 可以将信号电压...
6 《前置放大器设计与应用》实验补充资料一、有关...与对共模信号的电压放大倍数 Avc 之比,英文全称是 ...运算放大器和仪表放大器都具有一定的共模抑制特性。 ...
仪表放大器的正确使用方法_信息与通信_工程科技_专业资料。本文介绍了仪表放大...由于采用运算放大器,仪表放大器电路 的输入缓冲级 A1 和 A2 可以将信号电压...
热门文档