文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 计算机硬件及网络 > 运算放大器AD623英文资料
侵权投诉

运算放大器AD623英文资料

运算放大器AD623英文资料

AD623

plane. Maximum isolation between analog and digital is achievedby connecting the ground planes back at the supplies. The digi-tal return currents from the ADC, which flow in the analog groundplane will, in general, have a negligible effect on noise performance.If there is only a single power supply available, it must be sharedby both digital and analog circuitry. Figure 46 shows how tominimize interference between the digital and analog circuitry.As in the previous case, separate analog and digital ground

planes should be used (reasonably thick traces can be used as analternative to a digital ground plane). These ground planes

should be connected at the power supply’s ground pin. Separatetraces should be run from the power supply to the supply pins ofthe digital and analog circuits. Ideally, each device should haveits own power supply trace, but these can be shared by a num-ber of devices as long as a single trace is not used to route cur-rent to both digital and analog circuitry.

Ground Returns for Input Bias Currents

Input bias currents are those dc currents that must flow in orderto bias the input transistors of an amplifier. These are usuallytransistor base currents. When amplifying “floating” input sourcessuch as transformers or ac-coupled sources, there must be adirect dc path into each input in order that the bias current canflow. Figure 47 shows how a bias current path can be providedfor the cases of transformer coupling, capacitive ac-coupling andfor a thermocouple application. In dc-coupled resistive bridge

运算放大器AD623英文资料

applications, providing this path is generally not necessary as thebias current simply flows from the bridge supply through thebridge and into the amplifier. However, if the impedances thatthe two inputs see are large and differ by a large amount (>10k ),the offset current of the input stage will cause dc errors propor-tional with the input offset voltage of the amplifier.

Output Buffering

The AD623 is designed to drive loads of 10k or greater. If theload is less that this value, the AD623’s output should be buff-ered with a precision single supply op amp such as the OP113.This op amp can swing from 0 V to 4 V on its output whiledriving a load as small as 600 . Table III summarizes the per-formance of some other buffer op amps.

VOUT

Figure 48. Output BufferingTable III.Buffering Options

运算放大器AD623英文资料

Op Amp

TO POWERSUPPLYGROUNDVOUT

Comments

Single Supply, High Output Current

Rail-to-Rail Input and Output, Low Supply CurrentRail-to-Rail Input and Output, High Output Current

OP113OP191OP150

A Single Supply Data Acquisition System

Figure 47a.Ground Returns for Bias Currents with Transformer Coupled Inputs

运算放大器AD623英文资料

Interfacing bipolar signals to single supply analog to digitalconverters (ADCs) presents a challenge. The bipolar signalmust be “mapped” into the input range of the ADC. Figure 49shows how this translation can be achieved.

VOUT

TO POWERSUPPLYGROUND

Figure 47b.Ground Returns for Bias Currents with Thermocouple Inputs

运算放大器AD623英文资料

Figure 49.A Single Supply Data Acquisition System

运算放大器AD623英文资料

VOUT

TO POWERSUPPLYGROUND

Figure 47c.Ground Returns for Bias Currents with ACCoupled Inputs

The bridge circuit is excited by a +5V supply. The full-scaleoutput voltage from the bridge (±10mV) therefore has acommon-mode level of 2.5 V. The AD623 removes the common-mode component and amplifies the input signal by a factor of100 (RGAIN = 1.02k ). This results in an output signal of ±1V.In order to prevent this signal from running into the AD623’sground rail, the voltage on the REF pin has to be raised to atleast 1V. In this example, the 2V reference voltage from theAD7776 ADC is used to bias the AD623’s output voltage to 2V±1V. This corresponds to the input range of the ADC.–14–

REV. C

上一页第14页

你可能喜欢

热门文档

相关文档

  • 仪表放大器AD623

    AD620中文资料 20页 1下载券仪表放大器AD6...本文介绍的可编程增益运算放大器 AD623 很好 的 实现 了这 一功 能 .实 ...

  • 仪表放大器AD623在数采系统中的应用

    系统中的应用_计算机硬件及网络_IT/计算机_专业资料...奉文介绍的可编程增益运算放大器AD623 禳好驰实褒... 英文刊名: 年,卷(期): 被引用次数: 王建新, ...

  • AD623单电源_工程科技_专业资料

    AD623单电源_工程科技_专业资料。介绍了AD623单电源的使用方法及设计要点AD623 单电源、电源限输出仪表放大器的原理及应 摘要: 介绍了美国 ADI 公司最新推出的...

  • AD623仪表放大器在数采系统中的应用-CN

    AD623仪表放大器在数采系统中的应用-CN_信息与通信_工程科技_专业资料。AD623维普资讯 http://www.cqvip.com 传感器与仪器仪表 仪表放大器 A63D2 在数采系统...

  • 运算放大器实战入门(下)

    运算放大器实战入门(下)_信息与通信_工程科技_专业资料。运算放大器实战入门(下)运算放大器实战入门( 运算放大器实战入门(下) 云南大学信息学院:何乐生 2010.4...

  • 仪表放大器相关资料

    仪表放大器的应用技巧 长期以来,为仪表放大器供电的传统方法是采用双电源或双极性电源,这具有允许正负输入摆幅和输出摆幅的明显优势。随著元器件技 术的发展,单 ...

  • 仪表运算放大器型号列表

    仪表运算放大器型号列表_信息与通信_工程科技_专业资料。仪表运算放大器——型号列表制造商 TI 公司 产品类别 仪表运算放大 器 产品型号 INA110KP INA111AP INA114AP...

  • 仪表放大器的正确使用方法

    仪表放大器的正确使用方法_电子/电路_工程科技_专业资料。非常好的资料...由于采用运算放大器,仪表放大器电路 的输入缓冲级 A1 和 A2 可以将信号电压...

  • 前置放大器的设计与应用

    6 《前置放大器设计与应用》实验补充资料一、有关...与对共模信号的电压放大倍数 Avc 之比,英文全称是 ...运算放大器和仪表放大器都具有一定的共模抑制特性。 ...

  • 仪表放大器的正确使用方法

    仪表放大器的正确使用方法_信息与通信_工程科技_专业资料。本文介绍了仪表放大...由于采用运算放大器,仪表放大器电路 的输入缓冲级 A1 和 A2 可以将信号电压...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email