Investigation of IMC Thickness Effect on the Lead-free Solder Ball Attachment Strength:
Comparison between Ball Shear Test and Cold Bump Pull Test Results
Fubin Song and S. W. Ricky Lee1, 2
1
Department of Mechanical Engineering
2
Electronic Packaging Laboratory/Center for Advanced Microsystems Packaging Hong Kong University of Science & Technology, Clear Water Bay, Kowloon, Hong Kong
Tel: +852-2358-7203, Fax: +852-2358-1543, E-mail: rickylee@ust.hk
1
method to reveal the effect of IMC growth. In the past few years, a cold bump (or ball) pull (CBP) test configuration has been developed. With a mini clamping jaw and a pulling cartridge, the conventional ball shear/wire pull equipment can be modified to perform solder ball pull tests. In addition to providing tensile loading, the CBP test configuration also minimizes the effect of solder mask interference (which may be critical in the ball shear test). However, since the CBP test method is relatively new and the equipment is not widely available, so far there are very few publications in the literature reporting the experimental results of solder ball pull tests.
The present study investigates the effect of IMC thickness on the attachment strength of Sn-3.5%Ag (SA) and Sn-4.0%Ag-0.5%Cu (SAC) lead-free solder balls with the CBP test method. For the purpose of comparison, the conventional solder ball shear test is conducted as well. An upgraded commercial test equipment (DAGE4000S) is employed to perform both ball pull and ball shear tests. The SA and SAC solder balls are attached to the package substrates (with ENIG and OSP pad surface finish, respectively) using the lead-free solder reflow profile. Afterwards, except those for base case reference, all specimens are put in an oven for thermal aging at 150oC. The high temperature storage continues for 1000 hours and some 1. Introduction
Due to environmental consciousness and legislative samples are removed from the oven at 100, 200, 500 and regulations, lead-free solders will soon replace most of 1000 hours. Some solder ball specimens are cross-sectioned conventional lead-containing solders in microelectronic for measuring the thickness of IMC while the others are components and systems. The current industrial trend shows subject to the CBP and the ball shear tests. Furthermore, that x%Sn-y%Ag-z%Cu alloys are preferred lead-free solders various pulling and shearing speeds are applied during the for most applications [1-3]. However, with high percentage of tests in order to observe the loading rate effect. tin and higher reflow temperature, the lead-free solders tend 2. Experimental Procedures to form more intermetallic compounds (IMCs) at the solder-Two types of substrate pad finishes were investigated in
pad interface. Excessive growth of IMCs may promote brittle this study: organic solderability preservative (OSP) and failure, weaken the solder joint strength, and affect the long electroless nickel/immersion gold (ENIG). The chemical term reliability. Therefore, it is essential to investigate the compositions of lead-free solder alloys used in this work are effect of IMC growth (usually in term of IMC thickness at the Sn-3.5%Ag and Sn-4.0%Ag-0.5%Cu. The objective of the solder-pad interface) on the integrity of solder joints (usually present study is to investigate the effect of the IMC growth on in term of solder ball attachment strength). the attachment strength of solder balls with different solder
The conventional method to evaluate solder ball alloys and pad finishes. The specimens under evaluation were attachment strength is the ball shear test (following JESD22-standard 0.76 mm (30 mils) spheres for PBGA applications. B117). However, from previous research results [4], it seems The substrates for solder ball attachment were BT laminates that the ball shear test cannot correlate the degradation of ball with a thickness of 0.36 mm. The solder bond pads were shear strength to the growth of IMC thickness too well. This solder-mask-defined with an opening of 0.635 mm in phenomenon should be due to the fact that IMCs are not that diameter. The solder balls attached to substrates were weak under the shear loading. In principle, brittle materials performed in a hot-air convective reflow oven, of which the should be more susceptible to the tensile loading than the peak temperature in the soldering profile for lead-free solders shear loading. Therefore, the ball pull test should be a better was 260°C, and the solder balls were kept at the peak Abstract
Ball pull test has emerged to be an attractive alternative to the traditional ball shear method for characterizing the attachment strength of solder interconnection. Since it is a relatively new development, so far there is not industrial standard to regulate this testing method. This paper describes firstly the formation and growth of intermetallic compound (IMC) at the interface of Sn-3.5%Ag and Sn-4.0%Ag-0.5%Cu reflow soldered on different types of substrate pad surface finishes. One type of surface finish is organic solderability preservative (OSP) and the other is immersion gold over electroless nickel (ENIG). This paper discusses the effect of IMC growth after soldering and thermal aging at 150℃. The attachment strength of solder balls with thermal aging is investigated by ball shear and cold bump pull (CBP) tests. The test configuration and the experimental data are reported in detail. The test results indicate that the CBP test method can reveal the brittle failure of solder joints with a higher sensitivity, especially under the fast pulling speed. As a result, the effect of IMC growth can be identified more easily. In addition to the correlation between the IMC thickness and the solder ball attachment strength, the micro-structure of IMC and the failure modes will be discussed as well.
Investigation of Solder Ball Attachment Processes ...Zhong, "The Effect of Ball Pad Metallurgy and ...Thickness L 30 MI Sphere Wth Square ppertures ...
Effect of Lead Content... 4人阅读 4页 2.00 Effect of dopant conte... 1人阅读 5页 2.00 Effect of a Trace of B... 3人阅读 4页 ...
Effect of cerium on microstructure and mechanical properties of Sn-Ag-Cu system lead-free solder_专业资料。维普资讯 http://www.cqvip.com Aalbeolea、『1...
Effect of cerium on microstructure and mechanical properties of Sn-Ag-Cu system lead-free solder_专业资料。维普资讯 http://www.cqvip.com Aalbeolea、『1...
热门文档