HIGH-TEMPERATURE OXYGEN SEPARATION MEMBRANES FOR USE IN THE SULFUR-IODIDE THERMOCHEMICAL CYCLE FOR HYDROGEN
PRODUCTION
1
Andrea Ambrosini,1 Terry Garino2 and Tina Nenoff1
Chemical and Bio Technologies, Sandia National Laboratories, PO
Box 5800, MS 0734, Albuquerque, NM 87185-0734 2
Ceramic Materials, Sandia National Laboratories, PO Box 5800,
MS 1411, Albuquerque, NM 87185-1411
stabilized, usually at about 14%. For absorption/desorption, multiple-cycle thermogravimetric analysis (TGA) was run on the single-phase samples. First the temperature was cycled three times between 50 - 850°C under an O2 atmosphere. This was followed by cycling between O2 (high pO2) and Ar or He (low pO2) atmospheres at a constant temperature of 850°C. PXRD studies were run before and after thermal study samples to confirm retention of the structure.
Introduction
Efficient and environmentally sound methods of producing hydrogen are of great importance to the US as we progress toward the H2 Economy. Current studies are investigating the use of high temperature systems driven by nuclear and/or solar energy to drive thermochemical cycles for H2 production. These processes are advantageous since they do not produce greenhouse gas emissions that are a result of hydrogen production from electrolysis or hydrocarbon reformation. Earlier studies have identified over 100 possible reaction cycles that produce H2 at high temperatures.1 Of the cycles identified as the most promising, many require the removal of O2 or H2 to push reaction equilibriums in favorable directions. Based on a previous extensive survey of over 100 thermochemical cycles, which took into account such metrics as efficiency, cost, number of steps, number and phases of reactants, among others, the Sulfur-Iodide (SI) cycle was deemed to be one of the most promising. As shown in Figure 1, the first step of the SI cycle involves the decomposition of H2SO4 into O2, SO2, and H2O at temperatures around 850 ºC. Removal of O2 from this reaction pushes the equilibrium towards dissociation, thus increasing the overall efficiency. The membrane required for this step must withstand the high temperatures and corrosive conditions inherent in this process. Perovskites are promising materials for such membranes due to their robustness and mixed ionic/electronic conductivities. A mixed ionic-electronic conductor would benefit the process by alleviating the need for an applied electrode across the membrane to balance the oxygen ion flux. To this end, dense ceramic membranes based on the double-substituted perovskite, AxSr1-xByCo1-yO3-δ (A=La, Y; B=Cr, Mn, Fe, Ni) were synthesized by solid state methods and structurally characterized using powder x-ray diffraction. TGA vs. temperature and oxygen partial pressure was performed to test the oxygen absorption and desorption properties of the material, while conductivity and permeability measurements are in process.
Results and Discussion
The double-substituted perovskites were indexed in the cubic Pm-3m (221) space group. Table 1 shows the compositions of the synthesized materials that were determined to be single phase, their lattice parameters, weight loss after reduction, and their average weight loss versus temperature and oxygen partial pressure. Yttria-stabilized zirconia (YSZ), a well-known ion conductor, is included in Table 1 for comparison purposes.
Figure 1 illustrates an example of a multiple-cycle TGA analysis. The first part of the graph shows the weight change as the temperature is cycled between 50-850 °C, under a constant flow of O2 gas. This describes an easily reversible temperature-swing adsorption/desorption of oxygen. The second part of the graph illustrates the reversible weight change as a function of oxygen partial pressure, by cycling the gas between O2 and Ar or He at a constant temperature of 850 °C. This implies that the material can transport oxygen across a membrane with an oxygen partial pressure differential. Post-TGA powder diffraction patterns reveal no structural changes after the temperature and gas treatments, demonstrating the robustness of the material. (Figure 2)

Experimental
Synthesis. Perovskite oxides were synthesized by the nitrate-citrate method.2 Metal nitrates were dissolved into 100 mL of deionized H2O. Citric acid was added in a 1:1 citric acid:metal cation molar ratio and the solution was heated to 90 ºC with stirring until water evaporated and then dried overnight in drying oven. Resulting powder was ignited at 350 ºC to burn off nitrates and citrates, ground with a mortar and pestle, and sintered at 1250 ºC for 24 hours.
Structural characterization. The materials were structurally characterized by powder x-ray diffraction (PXRD) on a Siemens D500 diffractometer (Cu Kα radiation, Bragg-Brentano geometry) and refined using the Jade 6.5+ 3 and FullProf 4 Rietveld refinement software.
Thermal studies. Thermal studies on samples determined to be single-phase were performed using a TA Instruments STD 2960 DTA-TGA in order to obtain information on oxygen stability and oxygen adsorption/desorption. To estimate oxygen stoichiometry, samples were reduced under 5% H2/N2 at 1000°C until weight loss
Figure 1. TGA of La0.1Sr0.9Co0.7Mn0.3O3-δ. The crosses mark where the atmosphere was changed between O2 and He.
The most promising material thus far is the La0.1Sr0.9Co1-MnxxO3-δ perovskite. As shown in Table 1, the oxygen sorption properties increase with increasing Mn doping. Studies are currently underway to determine the extent of this solid solution and the composition of greatest oxygen conductivity.
Ongoing work involves the determination of the conductivity and permeation of these materials. For conductivity purposes, a four-point conductivity test instrument has been designed and built. Measurements have begun on samples of synthesized materials as well as on standard materials (YSZ), for comparison. Pressed and heat-treated powder samples are machined into bars nominally 2mm x 2 mm x 20 mm. Platinum wires are then wrapped around the bars at four places, both ends and just inside each end. Conducting paint
Prepr. Pap.-Am. Chem. Soc., Div. Fuel Chem. 2004, 49(2),841
Separation Oxygen-enriched Method and the Influence of Temperature and Magnetic...High-purity nitrogen (99.999%) with known volume and oxygen concentration ...
Separation of Acearyle... 8人阅读 6页 2.00 High Temperature Separ... 6人阅读 7页 2.00 Comparative Studies of... 1人阅读 6页 2.00...
High-Temperature Sulfur Removal in_电子/电路_工程科技_专业资料。High-...Ketene Air Separation Unit (ASU) Coal Low Temp Gas Cooling What is IGCC?...
The low-temperature region (up to SOVC) is kinetic in which the surface reaction rate of oxygen with carbon is limited. For the high-temperature ...
high-temperature gas separation and catalytic membrane reactors as well as ...S. Synthesis and Oxygen Permeation Properties of Thin YSZ/Pd Composite ...
A High-Performance Gas-Separation Membrane_工学_高等教育_教育专区。Angewandte...We crystallized small ZIF-90 particles at room temperature by the rapid ...
Moreover, direct one-step water splitting (thermolysis) requires the energy intensive process of high temperature oxygen–hydrogen separation coupled with ...
Single step separation for high-purity oxygen ? 100% selective for oxygen ...Can be integrated with other high temperature processes to produce electrical ...
High temperature brazing... 6页 2财富值 high temperature deforma... 4页... in contradistinction to the assumed separation of energy scales of previous ...
If simple and affordable air separation methods are successfully developed, ...cient. A high-temperature furnace using oxygen enrichment membranes has been ...
热门文档