DIN-1683-1998
DEUTSCHE NORMAugust 1998
Rough steel castings
General tolerances and machining allowances
(For replacement purposes only)
{
1683-1
Supersedes
October 1980 edition.
ICS77.140.80
Descriptors:General tolerances, machining allowances, castings, steel.Gußrohteile aus Stahlguß – Allgemeintoleranzen, Bearbeitungszugaben(Nicht für Neukonstruktionen)
In keeping with current practice in standards published by the International Organization for Standardization(ISO), a comma has been used throughout as the decimal marker.
Dimensions in mm
1Scope and field of application
This standard specifies general tolerances and machining allowances for rough castings of cast steel whichare subject to the technical delivery conditions laid down in such standards as DIN 1681, DIN 17245 orthe Stahl-Eisen-Werkstoffblatt (Iron and steel material specification) 510-62.
Users of this standard should note that it now only applies to castings used for repair and replacementpurposes. New designs are covered by ISO 8062:1994.
Owing to the lack of empirical data, general tolerances have not been specified here for angular dimensions.If angles are to meet accuracy requirements, these shall be indicated as individual tolerances.
2Normative references
This standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the titles of the publications arelisted below. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this standard only when incorporated in it by amendment or revision. For undated references, thelatest edition of the publication referred to applies.DIN 1680-1DIN 1681DIN 7182-1DIN 17245
Rough castings – General tolerances and machining allowances – General
Cast steel for general engineering purposes – Technical delivery conditionsSizes, deviations, tolerances and fits – Basic concepts
Ferritic steel castings with elevated temperature properties – Technical deliveryconditions
ISO 8062:1994Castings – System of dimensional tolerances and machining allowancesStahl-Eisen-Werkstoffblatt 510-62*)
3Concepts
See DIN 7182-1 and DIN 1680-1 for the terms ‘general tolerances’ and ‘tolerance grade’, and DIN 1680-1for a definition of ‘machining allowance’.
*) Obtainable from Verlag Stahleisen GmbH, Postfach 10 51 64, D-40042 Düsseldorf.
Continued on pages 2 to 4.
Translation by DIN-Sprachendienst.
In case of doubt, the German-language original should be consulted as the authoritative text.
©No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin.
Beuth Verlag GmbH, D-10772Berlin, has the exclusive right of sale for German Standards (DIN-Normen).
Ref.No.DIN1683-1:1998-08
English price group06
Sales No.0106
11.98
DEUTSCHE NORM December 2006 DIN 509 ICS 01.100.20; 25.020 Supersedes DIN 509:1998-06 D Technical drawings – Undercuts – Types and dimensions ...
2 其它标准和规范若在本标准中不作另行规定,则应同时遵循下述各标准与规范: DIN 4115 DIN 8563 DIN 8563 DIN 15018 DIN 17100 房屋建筑中的轻型钢结构和钢管...
DIN18273-1997 建筑五金件.防火门和防烟门把手组件.术语定义、尺寸、 要求和试验_建筑/土木_工程科技_专业资料。DIN 18273-1997 建筑五金件.防火门和防烟门...
DEUTSCHE NORM Dezember 2004 DIN EN 13209-1 ICS 97.190 X Artikel für ...ndig in den in EN 71-1:1998 festgelegten Prüfzylinder für Kleinteile ...
DIN 19522-2000 铸铁插口排水管和管件_建筑/土木_工程科技_专业资料。铸铁排水管欧洲标准。EN877标准Als Papierkopie - kein ?nderungsdienst / Printed copy - ...
DIN EN 10243-1-2005_专业资料。德标Correction in table 6, last line, ... DIN EN 1748-1-1-2004 DIN EN 1876-1-1998 DIN EN 10083-1-1996...
(includes amendment A1:2001); German Version EN 10222-4:1998 + A1:2001 { EN 10222-4 Ersatz für DIN EN 10222-4:1999-02 Pièces forgées ...
德国的文本 EN 50625-2-2 : 1998。 DIN EN5 0625-2-4 (VDE 0482 部分 266-2-4) 公共的检验情况用于在燃烧情况下的电线和绝缘体导线—由电线以及绝缘体 ...
0104 第 2 页 DIN 5480 第 11 部分 模数 6 (ρ fmin = 0,96)(关于插图1,请参见第1页)表1 基本尺寸 基准直径数 齿度圆直径 z 分圆直径 基径顶圆直...
Din 40431-2 塞规_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 Din 40431-2 塞规_机械/仪表_工程科技_专业资料。 ...
热门文档