DIN-1683-1998
Page2
DIN1683-1:1998-08
4
4.1
Tolerance grades
Dimensional deviations
For steel rough castings, dimensional deviations are largely dependent on
a)the dimensional accuracy of the pattern, the degree of shrinkage dependent on the material type andcasting configuration, the care taken during moulding and casting, and the moulding and casting equipmentused based on the batch size;b)the nominal sizes.
4.2Application of tolerance grades
Limit deviations shall be specified on the basis of the tolerance grades given in tables 2 and 3. Linear dimensionsand thickness shall be specified for the same grade; for exceptions see DIN 1680-1.
4.3Nominal size ranges
The nominal size ranges shown in the tables for each tolerance grade have been selected on the basis of reliablemeasurement data. For sizes outside the range for a given grade, the next coarsest grade applies.
4.4Radii
In the case of internal and external radii, the tolerance zone given in table 2 shall always be positioned so as toensure that the lower deviation is equal to zero.EXAMPLE:
Given a nominal size of 20 mm and tolerance grade GTB 18 as in table 2, the corresponding general toleranceshall be t3 mm. The lower limit for the radii is then zero and the upper limit is 6 mm.
To reduce the risk of cracking, internal radii shall comply with the values given in table 1 as a function of the wallthickness.
Table 1:Minimum values for internal radii
WallthicknessUp to 10Over 10 up to 30Over 30
0,33×wall thickness
Minimuminternal radius
5Machining allowances
The machining allowance, BZ, is a function of the largest external dimension of the casting and is the same forall tolerance grades (cf. table 4); see DIN 1680-1 for exceptions.
For sizes up to 500 mm, machining allowances may be reduced to approximately half the values specified intable 4 if the pattern equipment, casting procedure and machining procedure with regard to clamping surfacesand datum surfaces have been optimized, for example, for series production, as agreed between the customerand the foundry. These reduced values are shown in table 5.
6Designation
Where both the tolerance grade and the machining allowance have been selected on the basis of this standard,the designation of a grade GTB 17 tolerance (GTB 17) in conjunction with a machining allowance of 6 (BZ 6),for example, shall be designated as follows:
Tolerance and machining allowance DIN 1683 – GTB 17 – BZ 6
See DIN 1680-1 for other examples of designations.
DEUTSCHE NORM December 2006 DIN 509 ICS 01.100.20; 25.020 Supersedes DIN 509:1998-06 D Technical drawings – Undercuts – Types and dimensions ...
2 其它标准和规范若在本标准中不作另行规定,则应同时遵循下述各标准与规范: DIN 4115 DIN 8563 DIN 8563 DIN 15018 DIN 17100 房屋建筑中的轻型钢结构和钢管...
DIN18273-1997 建筑五金件.防火门和防烟门把手组件.术语定义、尺寸、 要求和试验_建筑/土木_工程科技_专业资料。DIN 18273-1997 建筑五金件.防火门和防烟门...
DEUTSCHE NORM Dezember 2004 DIN EN 13209-1 ICS 97.190 X Artikel für ...ndig in den in EN 71-1:1998 festgelegten Prüfzylinder für Kleinteile ...
DIN 19522-2000 铸铁插口排水管和管件_建筑/土木_工程科技_专业资料。铸铁排水管欧洲标准。EN877标准Als Papierkopie - kein ?nderungsdienst / Printed copy - ...
DIN EN 10243-1-2005_专业资料。德标Correction in table 6, last line, ... DIN EN 1748-1-1-2004 DIN EN 1876-1-1998 DIN EN 10083-1-1996...
(includes amendment A1:2001); German Version EN 10222-4:1998 + A1:2001 { EN 10222-4 Ersatz für DIN EN 10222-4:1999-02 Pièces forgées ...
德国的文本 EN 50625-2-2 : 1998。 DIN EN5 0625-2-4 (VDE 0482 部分 266-2-4) 公共的检验情况用于在燃烧情况下的电线和绝缘体导线—由电线以及绝缘体 ...
0104 第 2 页 DIN 5480 第 11 部分 模数 6 (ρ fmin = 0,96)(关于插图1,请参见第1页)表1 基本尺寸 基准直径数 齿度圆直径 z 分圆直径 基径顶圆直...
Din 40431-2 塞规_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 Din 40431-2 塞规_机械/仪表_工程科技_专业资料。 ...
热门文档