SSD590编码器说明书 590编码器安装调试等,参数设置SSD590编码器说明书 590编码器安装调试等,参数设置
8
$SSOLFDWLRQ#1RWHV
$GMXVWLQJ#WKH#&XVWRPHU#&DOLEUDWHG#2SWLRQ#$+6;:::88334The Encoder Receiver Option can be ordered for standard supply voltages of 5, 12, 15 and 24V
dc. For applications requiring different voltages, the Customer Calibrated option
(AH387775U001) can be purchased and the following procedure used to adjust the output
voltage setting.
1. Install the Encoder Receiver Option card on the drive. Do NOT connect it to the encoder yet.
2. Power-up the drive.
3. Measure the voltage between terminals E1 and E2. This voltage can range from 5V to 24Vdc.
4. Adjust the adjustment potentiometer until the desired output voltage is reached.
5. Connect the encoder and re-check the voltage at the encoder terminals.
1RWH=#,I#WKH#YROWDJH#GURSV#PRUH#WKDQ#RQH#YROW/#FKHFN#WKH#HQFRGHU#ZLULQJ#IRU#H[FHVVLYH#ORDGLQJ1$GMXVWLQJ##WKH#DGMXVWPHQW#SRWHQWLRPHWHU#WR#FRPSHQVDWH#IRU#DQ#H[FHVVLYH#OLQH#YROWDJH#GURSLV#QRW#UHFRPPHQGHG1
Figure 3 shows the terminal designations and the location of the adjustment potentiometer. Incases where the encoder receiver card or the motor controller cannot supply enough power forthe encoder, use an external power supply. The supply should be isolated from ground, that isneither the 0V dc nor the +V dc should be connected to ground.
All wiring to the Encoder Receiver Option board should be in screened cable. Cable with anoverall screen or a screen over each individual pair may be used. Connection to earth shouldalways be made at the receiver end ONLY, and should be in a star configuration. Take specialcare wiring the encoders to the option board due to the low-level of the signals.
(QFRGHUV#ZLWK#&RPSOHPHQWDU\#2XWSXWV

E3 - A Channel
E5 - B Channel
Figure 3 Terminal Designations
(QFRGHU#5HFHLYHU#2SWLRQ0#+$6;;;9:
欧陆590直流调速器说明书派克SSD590直流调速器说明书_工程科技_专业资料。欧陆...4-4 ?? ? 微 测速器 /编码器反馈选项板 ...………......
SSD590C直流调速器编码器反馈参数的详细设置方法 隐藏>> SSD590C 直流调速器编码器反馈参数的详细设置方法 SSD590C 直流调速器编码器反馈参数的详细设置方法 关于 ...
新欧陆SSD590调速器中英文对照报警说明_工学_高等教育_教育专区。编号 报警英文... 操作长度—参阅微 型测速器手册检查 电缆和编码器的连 接 5 OVERVOLTS (VA)...
(编码反馈) ,选择反馈方式 是根据所选的配件板及实际电机使用的反馈方式,然后...先根据电机的名牌参数, 参照 SSD590 系列使用手册中文说明书第 51, 页的说明...
SSD590 系列直流调速器的一般调试步骤 SSD590 系列直流调速器的一般调试步骤归纳如下: 1. 先根据电机的名牌参数,参照 SSD590 系列使用手册中文说明书第 51~52 页...
3、 编码器的设定参数:首先在速度反馈中选择编码器反馈选项,然后在参数设定编 ...590C 调速器的快速设定 SSD590C直流调速器参数快速设置说明 通电开机后按M键...
SSD590C直流调速器弱磁升速操作方法及参数设定_电子/电路_工程科技_专业资料...3. 将 SSD590C 直流调速器的反馈方式改成测速反馈或者编码器反馈,SETUP ...
SSI信号绝对值编码器说明书_电子/电路_工程科技_专业资料。SSI信号的绝对值编码器 JFAM6010R12CSGBXXX 说明书☆ 绝对值码盘,高精度全数字化,无信号干扰、零点飘移之...
(编码器) ▲和▼ 键设定编码器的线数 ENCODER PRM ▲和▼ 键设定最大速度...五、 一般调试步骤: 1. 先根据电机的名牌参数,参照 SSD590 系列使用手册中文...
编码器使用说明书_机械/仪表_工程科技_专业资料。编码器的使用说明介绍1.※有网友问:增量旋转编码器选型有哪些注意事项? 应注意三方面的参数: 1. 械安装尺寸,...
热门文档