超高压电
Two Phase Convective Cooling for Ultra-High Power Dissipation in Microprocessors
Peter A. Kottke, Thomas M. Yun, Craig E. Green, Yogendra K. Joshi, Andrei G. Fedorov*
George W. Woodruff School of Mechanical Engineering
Georgia Institute of Technology Atlanta, GA, U.S.A. 30332 *Email: agf@gatech.edu
INTRODUCTION
One potential approach to dissipating hig`h heat fluxes at relatively low temperatures to meet design needs for high performance microprocessors is through forced convection boiling heat transfer [1-5]. Such two-phase cooling offers the benefit of high heat transfer coefficients and exploits both latent and sensible heat transfer. One disadvantage is flow instability, which can be problematic, in particular when using parallel flow through microchannels [1,5]. Microgaps, with and without pin fins, may minimize or altogether eliminate this disadvantage [2-4], and are thus an area of increased recent attention, including this work.
Another challenge in the design of systems in which convective boiling dominates is lack of tractable first-principles models to predict heat transfer coefficients and other flow and temperature parameters. As the required complexity of models increases, the ability to parametrically explore a design space with reasonable effort, and to identify general trends, decreases. And as the level of empiricism brought into models increases, the ability to reliably apply the models to conditions outside those for which their underlying empiricisms were developed also decreases. In this work, we adopt the approach of initially using a first principles thermodynamic model to identify trends related to coolant selection and overall design strategy for microgap cooling for very demanding applications, with high heat fluxes (1 kW/cm2) and in which the coolant is nearly entirely vaporized. Having used the highly idealized model to identify a potential trend of improving heat transfer performance with increased system pressure, we then augment the model to include entrance and exit pressure drop effects, both to see how these effects impact the initial conclusions, and to assess the penalty (reduced system COP) that accompanies higher-pressure operation. Finally, we assess the potential impact of frictional pressure drop on the conclusions from idealized thermodynamic analysis through use of a reduced order 1-D two-phase hydrodynamic model.
THERMODYNAMIC ANALYSIS
A thermodynamic model enables rapid assessment of tradeoffs and recognition of trends for performance comparison of a variety of candidate coolants based on first principles, independent of empirical correlations. Our thermodynamic model imposes mass, energy and momentum conservation on a control volume that consists of all fluid within the microgap. The pressure drop from inlet to outlet is due only to acceleration, and is the minimum possible for a given coolant, mass flow rate, inlet state, and outlet quality. The resulting conclusions, although obtained for ideal conditions, provide a starting point for more detailed investigation presented later in this paper. We explore a broad portfolio of coolants with properties available in the
ABSTRACT
We present results of modeling for the design of microgaps for the removal of high heat fluxes, i.e., 1 kW/cm2, at low wall temperature (~ 85ºC) via a strategy of very high mass flux (>1000 kg/m2s), high quality (outlet vapor mass quality > 90%), two-phase forced convection. Modeling includes (1) thermodynamic analysis to obtain performance trends across a wide range of candidate coolants, (2) evaluation of worst-case pressure drop due to contraction and expansion in inlet/outlet manifolds, and (3) 1-D reduced order simulations to obtain realistic estimates of different contributions to the pressure drops. The main result is the identification of a general trend of improved heat transfer performance at higher system pressure at the cost of reduced achievable system efficiency (COP), with important implications for coolant selection and system design.
KEY WORDS: microelectronics cooling, microchannel boiling heat transfer, microgap
NOMENCLATURE d hydraulic diameter, m f Fanning friction factor g acceleration due to gravity, 9.8 m/s2 G mass flux, kg/(m2s) H microgap height, m h specific enthalpy, J/(kg K) k thermal conductivity, W/(m K) L microgap length, m n power law exponent P pressure, Pa Q' heat transfer rate per unit depth, W/ m Re Reynolds number q'' heat flux, W/m2 T temperature, K v specific volume, m3/kg x vapor mass quality X Martinelli parameter z distance in flow direction from inlet, m Greek symbols
void fraction
two-phase multiplier ρ mass density, kg/m3 surface tension, N/m
Subscripts f due to friction l saturated liquid lv change from saturated liquid to vapor in inlet out outlet v saturated vapor
978-1-4799-5267-0/14/$31.00 ©2014 IEEE 199 14th IEEE ITHERM Conference
www.elsevier.com/locate/ijhmt Investigation of the two-phase convective ...in COP for HFO-1234yf system at a same cooling capacity with HFC-134a....
CFD simulation of convective flow boiling of refrigerant in a vertical ... of the wall lubrication force is necessary for the adiabatic two-phase ?...
upon the merits of phase change to achieve the desired cooling performance....Two key merits of boiling in microchannels are (1) very large convective ...
Convective WeatherConvective Weather隐藏>> Convective...Stages of Air Mass Thunderstorms Cumulus Phase ? ...? Produces temporary cooling ? Slight potential ...
two-phase mixture level, which directly determines the cooling capability and...(2003) can be applied to convective and pool systems; in addition, ...
economic and effective methods in producing ultra-... is considered to satisfy the convective equation ...Hence for E / E0 1, the laminar two-phase ...
Cooling Electronics with Nanofluids Laminar Convective Nanofluids Nanofluids Nan...Horizontal Tube Using Two-Phase Mixture Model,” Applied Thermal Engineering,...
principle and its applications in enhancing single phase convective_工学_高等... it can be seen that there are two disadvantages for the existing ...
(2005)Forced convective heat transfer across a ...singlephase [1–4] and boiling (two-phase ow)...for electronic cooling heat sinks have been ...
热门文档